模具术语英文翻译
根据国家标准,以下为部分塑料模具成形术语的标准翻译。
动模 Movable Mould Moving Half
定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate
动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate
下模座板 Lower Clamping Plate
凹模固定板 Cavity-retainer Plate
型芯固定板 Mould Core-retainer Plate
凸模固定板 Punch-retainer Plate
模套 Die Body Die Sleeve Die Blank
支承板 Backing Plate Support Plate
垫块 Spacer Parallel
支架 Ejector Housing Mould Base Leg
模头 Die Head
根据国家标准,以下为部分压铸模具术语的标准翻译。
压力铸造模具 Die-Casting Die
压铸模零部件
定模 Fixed Die Cover Die
定模座板 Fixed Clamping Plate
定模套板 Bolster Fixed Die
动模 Moving Die Ejector Die
动模座板 Moving Clamping Plate
直流道 Sprue
横流道 Runner
内浇口 Gate
模具分类
Injection Mold 注塑模
Plastic Rubber Mould 塑胶模
Rubber Molding 橡胶成形
Hot Chamber Die Casting 热室压铸
Sand Mold Casting 砂模铸造
Extrusion Mold 挤出模
Multi-Cavity Mold 多模穴模具
Stack Mold, Stack Injection Mould 叠层模
Plaster Mold 石膏模
Three Plates Mold 三板模
Plain Die 简易模
Pierce Die 冲孔模
Forming Die 成型模
Progressive Die 连续模
Gang Dies 复合模
Shearing Die 剪边模
Cavity Die 型腔模
Riveting Die 铆合模
Compression Molding 压缩成型
Flash Mold 溢流式模具
Extrusion Mold 挤压式模具
Split Mold 分割式模具
Mould Cavity 型腔母模
Mold Core 模芯公模
Large Die Mold 大型模具
Precise Die Mold 精密模具
Complex Die Mold 复杂模具
Foaming Mould 发泡模具
Metal Die 金属模具
Plastic Mold 塑料模具
Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具
Graphite Die 石墨模具
流道浇口部分
Runner System 浇道系统
Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆
Runner Design 流道设计
Main Runner 主流道
Secondary Runner 次流道
Mould Gate Design 浇口设计
Submarine Gate 潜伏浇口
Tunnel Gate 隧道式浇口
Pinpoint Gate 点浇口
Fan Gate 扇形浇口
Side Gate 侧浇口
Edge Gate 侧缘浇口
Tab Gate 搭接浇口
Film Gate 薄膜浇口
Flash Gate 闸门浇口
Slit Gate 缝隙浇口
Dish Gate 盘形浇口
Diaphragm Gate 隔膜浇口
Ring Gate 环形浇口
Runnerless 无浇道
Sprueless 无射料管方式
Long Nozzle 延长喷嘴方式
Sprue 浇口,溶渣
Insulated Runner Hot Runner 热浇道
Runner Plat 浇道模块
Valve Gate阀门浇口
Slag Well 冷料井
Cold Slag 冷料渣
Sprue Gate 射料浇口,直浇口Nozzle 射嘴
Sprue Lock Pin 料头钩销(拉料杆)注塑缺陷
Flash 飞边
Warpage 翘曲
Air Trap 积风
Blush 发赤
Flow Line 流痕
Splay 银纹
Short Shot 短射
Sink Mark 缩痕
Streak 条纹
Void 缩孔
Weld Line 熔接线
Gas Mark 烧焦
Cold Slug 冷斑
Delamination 起皮
Burr 毛刺
Flaw Scratch 刮伤
Gloss 光泽
Glazing 光滑
Surface Check 表面裂痕
Hesitation 迟滞
注塑工艺
Molding Conditions 成型条件Drying 烘干
Barrel Temperature 料筒温度
Melt Temperature 熔化温度
Mold Temperature 模具温度Injection Pressure 注塑压力
Back Pressure 背压
Injection Speed 注塑速度
Screw Speed 螺杆转速
Tensile Strength 抗拉强度
Tensile Elongation 延伸率Flexural Modulus 弯曲模数Flexural Strength 抗弯强度Shrinkage 收缩率
Regrind Usage 次料使用
Moulding 模塑
机械设备
Lathe 车床
Planer 刨床
Miller Milling Machine 铣床
Grinder 磨床
Driller 钻床
Linear Cutting 线切割
Electrical Sparkle 电火花
Welder 电焊机
Punching Machine 冲床
Robot 机械手
Common Equipment 常用设备
EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机
Contouring Machine 轮廓锯床
Copy Grinding Machine 仿形磨床
Cylindrical Grinding Machine 外圆磨床
Die Spotting Machine 合模机
Engraving Machine 雕刻机
Engraving E.D.M 雕模放置加工机
Form Grinding Machine 成形磨床
, Graphite Machine 石墨加工机
Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床
模具零件
Top Plate 上托板(顶板)
Top Block 上垫脚
Punch Set 上模座
Punch Pad 上垫板
Punch Holder 上夹板
Stripper Pad 脱料背板
Up Stripper 上脱料板
Male Die 公模(凸模)
Feature Die 公母模
Female Die 母模(凹模)
Upper Mold Plate 上模板
Lower Mold Plate 下模板
Die Pad 下垫板
Die Holder 下夹板
Die Set 下模座
Bottom Block 下垫脚
Bottom Plate下托板(底板)
Stripping Plate 内外打(脱料板)
Outer Stripper 外脱料板
Inner Stripper 内脱料板
Lower Stripper 下脱料板
Inner Guiding Post 内导柱
Inner Hexagon Screw 内六角螺钉
Dowel Pin 固定销
Mould Coil Spring 模具弹簧
Lifter Pin 顶料销
Isoheight Sleeve 等高套筒
Pin 销
Lifter Guide Pin 浮升导料销
Guide Pin 导正销
Wire Spring 圆线弹簧
Outer Guiding Post 外导柱
Stop Screw 止付螺丝
Located Pin 定位销
Outer Bush 外导套
Punch 冲头
Insert 入块(嵌入件)
Deburring Punch 压毛边冲子
Groove Punch 压线冲子
Stamped Punch 字模冲子
Round Punch 圆冲子
Special Shape Punch 异形冲子
Bending Block 折刀
Roller 滚轴
Baffle Plate 挡块
Located Block 定位块
Supporting Block for Location 定位支承块Air Cushion Plate 气垫板
Air-Cushion Eject-rod 气垫顶杆
Trimming Punch 切边冲子
Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子
Reel-stretch Punch 卷圆压平冲子
Guide Plate 定位板
Sliding Block 滑块
Sliding Dowel Block 滑块固定块
Active Plate 活动板
Lower Sliding Plate 下滑块板
Upper Holder Block 上压块
Upper Mid Plate 上中间板
Spring Box 弹簧箱
Spring-Box Eject-rod 弹簧箱顶杆
Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套
Cover Plate 盖板
Guide Pad 导料块
模具技术用语
各种常用模具成形方式
Accurate Die Casting 精密压铸
Powder Forming 粉末成形
Calendaring Molding 压延成形
Powder Metal Forging 粉末锻造
Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造
Cold Forging 冷锻
Press Forging 冲锻
Compacting Molding 粉末压出成形
Rocking Die Forging 摇动锻造
Compound Molding 复合成形
Rotary Forging 回转锻造
Compression Molding 压缩成形
Rotational Molding 离心成形
Dip Mold 浸渍成形
Rubber Molding 橡胶成形
Encapsulation Molding 注入成形
Sand Mold Casting 砂模铸造
Extrusion Molding 挤出成形
Shell Casting 壳模铸造
Foam Forming 发泡成形
Sinter Forging 烧结锻造
Forging Roll 轧锻
Six Sides Forging 六面锻造
Gravity Casting 重力铸造
Slush Molding 凝塑成形
Hollow Blow Molding 中空(吹出)成形Squeeze Casting 高压铸造
Hot Chamber Die Casting 热室压铸
Swaging 挤锻
Hot Forging 热锻
Transfer Molding 转送成形
Injection Molding 射出成形
Warm Forging 温锻
Investment Casting 精密铸造
Matched Die Method 对模成形法
Laminating Method 被覆淋膜成形
Low Pressure Casting 低压铸造
Lost Wax Casting 脱蜡铸造
Matched Mould Thermal Forming 对模热成形模Close Mold 合模
Demould 脱模脱模剂
Mould Unloading 开模
Eject 顶出
Tool Change Retooling Die Changing 换模Mould Clamping 锁模
各式模具分类用语
Bismuth Mold 铋铸模
Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模
Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模
Loading Shoe Mold 料套式模具
Center-Gated Mold 中心浇口式模具
Loose Detail Mold 活零件模具
Chill Mold 冷硬用铸模
Loose Mold 活动式模具
Cold Hobbing 冷挤压制模法
Louvering Die 百叶窗冲切模
Composite Dies 复合模具
Manifold Die 分歧管模具
Counter Punch 反凸模
Modular Mold 组合模具
Double Stack Mold 双层模具
Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模
Multi-Gate Mold 复式浇口模具
Expander Die 扩径模
Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模
Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具
Plaster Mold 石膏模
Blank Through Dies 漏件式落料模
Porous Mold 通气性模具
Duplicated Cavity Plate 复板模
Positive Mold 全压式模具
Fantail Die 扇尾形模具
Pressure Die 压紧模
Fishtail Die 鱼尾形模具
Profile Die 轮廓模
Flash Mold 溢料式模具
Progressive Die 顺序模
Gypsum Mold 石膏铸模
Portable Mold 手提式模具
Hot-Runner Mold 热流道模具
Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模
Punching Die 落料模
Lancing Die 切口模切缝模
Raising(Embossing)压花起伏成形
Re-entrant Mold 倒角式模具
Sectional Die 拼合模
Runless Injection Mold 无流道冷料模具Sectional Die 对合模具
Segment Mold 组合模
Semi-Positive Mold 半全压式模具<, /SPAN> Shaper 定型模套
Single Cavity Mold 单腔模具
Solid Forging Die 整体锻模
Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模
Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模
Swing Die 振动模具
Three Plates Mold 三片式模具Trimming Die 切边模
Unit Mold 单元式模具
Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模
模具厂常用之标准零配件
Air Vent Valve 通气阀
Anchor Pin 锚梢
Angular Pin 角梢
Baffle 调节阻板
Angular Pin 倾斜梢
Baffle Plate 折流档板
Ball Button 球塞套
Ball Plunger 定位球塞
Ball Slider 球塞滑块
Binder Plate 压板
Blank Holder 防皱压板
Blanking Die 落料冲头
Bolster 上下模板
Bottom board 浇注底板
Bolster 垫板
Bottom Plate 下固定板
Bracket 托架
Bumper Block 缓冲块
Buster 堵口
Casting Ladle 浇注包
Casting lug 铸耳
Cavity 模穴(模仁)
Cavity Retainer Plate 模穴托板Center Pin 中心梢
Clamping Block 锁定块
Coil Spring 螺旋弹簧
Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓
Core 心型
Core Pin 心型梢
Cotter 开口梢
Cross 十字接头
Cushion Pin 缓冲梢
Diaphragm Gate 盘形浇口
Die Approach 模头料道
Die Bed 型底
Die Block 块形模体
Die Body 铸模座
Die Bush 合模衬套
Die Button 冲模母模
Die Clamper 夹模器
Die Fastener 模具固定用零件
Die Holder 母模固定板
Die Lip 模唇
Die Plate 冲模板
Die Set 冲压模座
Direct Gate 直接浇口
Dog Chuck 爪牙夹头
Dowel 定位梢
Dowel Hole 导套孔
Dowel Pin 合模梢
Dozzle 辅助浇口
Dowel Pin 定位梢
Draft 拔模锥度
Draw Bead 张力调整杆
Drive Bearing 传动轴承
Ejection Pad 顶出衬垫
Ejector 脱模器
Ejector Guide Pin 顶出导梢
Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫
Ejector Pin 顶出梢
Ejector Plate 顶出板
Ejector Rod 顶出杆
Ejector Sleeve 顶出衬套
Ejector Valve 顶出阀
Eye Bolt 环首螺栓
Filling Core 填充型芯椿入蕊
Film Gate 薄膜形浇口
Finger Pin 指形梢
Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针
Flash Gate 毛边形浇口
Flask 上箱
Floating Punch 浮动冲头
Gate 浇口
Gate Land 浇口面
Gib 凹形拉紧楔
Goose Neck 鹅颈管
Guide Bushing 引导衬套
Guide Pin 导梢
Guide Post 引导柱
Guide Plate 导板
Guide Rail 导轨
Head Punch 顶头冲孔
Headless Punch 直柄冲头
Heavily Tapered Solid 整体模蕊盒
Hose Nippler 管接头
Impact Damper 缓冲器
Injection Ram 压射柱塞
Inlay Bush 嵌入衬套
Inner Plunger 内柱塞
Inner Punch 内冲头
Insert 嵌件
Insert Pin 嵌件梢
King Pin 转向梢
King Pin Bush 主梢衬套
Knockout Bar 脱模杵
Land 合模平坦面
Land Area 合模面
Leader Bush 导梢衬套
Lifting Pin 起模顶针起模杆
Lining 内衬
Locating Center Punch 定位中心冲头
Locating Pilot Pin 定位导梢
Locating Ring 定位环
Lock Block 压块
Locking Block 定位块
Locking Plate 定位板
Loose Bush 活动衬套
Making Die 打印冲子
Manifold Block 歧管档块
Master Plate 靠模样板
Match Plate 分型板
Mold Base 塑胶模座
Mold Clamp 铸模紧固夹
Mold Platen 模用板
Moving Bolster 换模保持装置
Moving Bolster Plate 可动侧模板
One Piece Casting 整体铸件
Parallel Block 平行垫块
Parting Line 分模线
Parting Lock Set 合模定位器
Pass Guide 穴型导板
Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子
Pin Gate 针尖浇口
Plate 衬板
Pre Extrusion Punch 顶挤冲头
Punch 冲头
Puncher 推杆
Pusher Pin 衬套梢
Rack 机架
Rapping Rod 起模杆
Re-entrant Mold 凹入模
Retainer Pin 嵌件梢
Retainer Plate 托料板
Return Pin 回位梢
Riding Stripper 浮动脱模器
Ring Gate 环型浇口
Roller 滚筒
Runner 流道
Runner Ejector Set 流道顶出器
Runner Lock Pin 流道拉梢
Screw Plug 头塞
Set Screw 固定螺丝
Shedder 脱模装置
Shim 分隔片
Shoe 模座之上下模板
Shoot 流道
Shoulder Bolt 肩部螺丝
Skeleton 骨架
Slag Riser 冒渣口
Slide(Slide Core)滑块
Slip Joint 滑配接头
Spacer Block 间隔块
Spacer Ring 间隔环
Spider 模蕊支架
Spindle 主轴
Sprue 注道
Sprue Bushing 注道衬套
Sprue Bushing Guide 注道导套
Sprue Lock Bushing 注道定位衬套
Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线
Square Key 方键
Square Nut 方螺帽
Square Thread 方螺纹
Limit Stop Collar 限位套
Stop Pin 止动梢
Stop Ring 止动环
Stopper 定位停止梢
Straight Pin 圆柱销
Stripper Bolt 脱料螺栓
Stripper Bushing 脱模衬套
Stripper Plate 剥料板
Stroke End Block 行程止梢
Submarine Gate 潜入式浇口
Support Pillar 支撑支柱顶出支柱
Support Pin 支撑梢
Supporting Plate 托板
Sweep Template 造模刮板
Tab Gate 辅助浇口
Taper Key 推拔键
Taper Pin 拔锥梢锥形梢
Teeming Pouring 浇注
Three Start Screw 三条螺纹
Thrust Pin 推力销
Tie Bar 拉杵
Tunnel Gate 隧道形浇口
Vent 通气孔
Wortle Plate 拉丝模板
模具常用之工作机械
3D Coordinate Measurement 三次元量床
Boring Machine 搪孔机
CNC Milling Machine CNC铣床
Contouring Machine 轮廓锯床
Copy Grinding Machine 仿形磨床
Copy Lathe 仿形车床
Copy Milling Machine 仿形铣床
Copy Shaping Machine 仿形刨床
Cylindrical Grinding Machine 外圆磨床
Die Spotting Machine 合模机
Drilling Machine 钻孔机
Engraving Machine 雕刻机
Engraving E.D.M 雕模放置加工机
Form Grinding Machine 成形磨床
Graphite Machine 石墨加工机
Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床
Jig Boring Machine 冶具搪孔机
Jig Grinding Machine 冶具磨床
Lap Machine 研磨机
Machine Center 加工制造中心
Multi Model Miller 靠磨铣床
NC Drilling Machine NC钻床
NC Grinding Machine NC磨床
NC Lathe NC车床
NC Programming System NC程式制作系统
Planer 龙门刨床
Profile Grinding Machine 投影磨床
Projection Grinder 投影磨床
Radial Drilling Machine 旋臂钻床
Shaper 牛头刨床
Surface Grinder 平面磨床
Try Machine 试模机
Turret Lathe 转塔车床
Universal Tool Grinding Machine 万能工具磨床Vertical Machine Center 立式加工制造中心Wire E.D.M 线割放电加工机
入水 Gate
进入位 Gate Location
水口形式 Gate Type
大水口 Edge Gate
细水口 Pin-point Gate
水口大小 Gate Size
转水口 Switching Runner Gate
唧嘴口径 Sprue Diameter
流道 Mold Runner
热流道 Hot Runner Hot Manifold
温度控制器温控器 Thermostat Thermoregulators Temperature Controller 热嘴冷流道 Hot Sprue Cold Runner
唧嘴直流 Direct Sprue Gate
圆形流道 Round Full Half Runner
流道电脑分析 Mold Flow Analysis
流道平衡 Runner Balance
热嘴 Hot Sprue
热流道板 Hot Manifold
发热管 Cartridge Heater
探针 Thermocouples
插头 Connector Plug
插座 Connector Socket
密封封料 Seal
运水 Water Line
喉塞 Line Plug Throat Taps
喉管 Tube
塑胶管 Plastic Tube
快速接头 Jiffy Quick Connector Quick Disconnect Coupling
模具零件 Mold Components
三板模 3-Plate Mold
二板模 2-Plate Mold
边钉导边 Leader Pin Guide Pin
边司导套 Bushing Guide Bushing
中托司 Shoulder Guide Bushing
中托边 Guide Pin
顶针板 Ejector Retainner Plate
托板 Support Plate
螺丝 Screw
管钉 Dowel Pin
开模槽 Ply Bar Scot
内模管位 Core Cavity inter-Lock
顶针 Ejector Pin
司筒 Ejector Sleeve
司筒针 Ejector Pin
推板 Eject Plate Push Plate Stripper Plate
缩呵 Movable Core Return Core Puller
扣机(尼龙拉勾) Nylon Latch Lock
斜顶 Lifter
模胚(架) Mold Base
上内模 Cavity Insert
下内模 Core Insert
行位(滑块) Slide
镶件 Insert
压座 Wedge
耐磨板油板 Wedge Wear Plate
压条 Plate
撑头 Support Pillar
唧嘴 Sprue Bushing
挡板 Stop Plate
定位圈 Locating Ring
锁扣 Latch
扣机 Parting Lock Set
推杆 Push Bar
栓打螺丝 S.H.S.B
顶板 Ejector Plate
活动臂 Lever Arm
分流锥 Sprue Spreader
分流板 Spreader Plate
水口司 Bush
垃圾钉 Stop Pin
隔片 Buffle
弹弓柱 Spring Rod
弹弓 Die Spring
中托司 Ejector Guide Bush
中托边 Ejector Guide Pin
镶针 Pin
销子 Dowel Pin
波子弹弓 Ball catch
喉塞 Pipe Plug
锁模块 Lock Plate
斜顶 Angle from Pin
斜顶杆 Angle Ejector Rod
尼龙拉勾 Parting Locks
活动臂 Lever Arm
复位键提前回杆 Early Return Bar
气阀 Valves
斜导边 Angle Pin
术语 Terms
承压平面平衡 Parting Surface Support Balance
模排气 Parting Line Venting
回针碰料位 Return Pin and Cavity Interference
顶针碰运水 Water Line Interferes with Ejector Pin 料位出上下模 Part from Cavith (Core) Side
不准用镶件 Do Not Use (Core Cavity) Insert
用铍铜做镶件 Use Beryllium Copper Insert
初步模图设计 Preliminary Mold Design
正式模图设计 Final Mold Design
弹弓压缩量 Spring Compressed length
稳定性好 Good Stability Stable
强度不够 Insufficient Rigidity
均匀冷却 Even Cooling
扣模 Sticking
热膨胀 Thermal Expansion
公差 Tolerance
铜公(电极) Copper Electrode Air Vent Valve 通气阀
Anchor Pin 锚梢
Angular Pin 角梢
Baffle 调节阻板
Angular Pin 倾斜梢
Baffle Plate 折流挡板
Ball Button 球塞套
Ball Plunger 定位球塞
Ball Slider 球塞滑块
Binder Plate 压板
Blank Holder 防皱压板
Blanking Die 落料冲头
Bolster 上下模板
Bottom Board 浇注底板
Bolster 垫板
Bottom Plate 下固定板
Bracket 托架
Bumper Block 缓冲块
Buster 堵口
Casting Ladle 浇注包
Casting Lug 铸耳
Cavity 模腔模穴(模仁)Cavity Retainer Plate 模穴托板Center Pin 中心梢
Clamping Block 锁定块
Coil Spring 螺旋弹簧
Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓
Core 心型
Core Pin 心型梢
Cotter 开口梢
Cross 十字接头
Cushion Pin 缓冲梢
Diaphragm Gate 盘形浇口
Die Approach 模头料道
Die Bed 型底
Die Block 块形模体
Die Body 模体
Die Body 铸模座
Die Bush 合模衬套
Die Button 冲模母模
Die Clamper 夹模器
Die Fastener 模具固定用零件Die Holder 母模固定板
Die Lip 模唇
Die Plate 冲模板
Die Set 冲压模座
Direct Gate 直接浇口
Dog Chuck 爪牙夹头
Dowel 定位梢
Dowel Hole 导套孔
Dowel Pin 合模梢
Dozzle 辅助浇口
Dowel Pin 定位梢
Draft 拔模锥度
Draw Bead 张力调整杆
Drive Bearing 传动轴承
Ejection Pad 顶出衬垫
Ejector 脱模器
Ejector Guide Pin 顶出导梢
Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫
Ejector Pin 顶出梢
Ejector Plate 顶出板
Ejector Rod 顶出杆
Ejector Sleeve 顶出衬套
Ejector Valve 顶出阀
Eye Bolt 环首螺栓
Filling Core 填充型芯椿入蕊
Film Gate 薄膜形浇口
Finger Pin 指形梢
Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针
Flash Gate 毛边形浇口
Flask 上箱
Floating Punch 浮动冲头
Gate 浇口
Gate Land 浇口面
Gib 凹形拉紧楔
Goose Neck 鹅颈管
Guide Bushing 引导衬套
Guide Pin 导梢
Guide Post 引导柱
Guide Plate 导板
Guide Rail 导轨
Head Punch 顶头冲孔
Headless Punch 直柄冲头
Heavily Tapered Solid 整体模蕊盒Hose Joint Pipe Coupler 管接头Impact Damper 缓冲器
Injection Ram 压射柱塞
Inlay Bush 嵌入衬套
Inner Plunger 内柱塞
Inner Punch 内冲头
Inserts 嵌件
Insert Pin 嵌件梢
King Pin 转向梢
King Pin Bush 主梢衬套
Knockout Bar 脱模杵
Land 合模平坦面
Land Area 合模面
Leader Bush 导梢衬套
Lifting Pin 起模顶针
Lining 内衬
Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢
Locating Ring 定位环
Lock Block 压块
Locking Block 定位块
Locking Plate 定位板
Loose Bush 活动衬套
Making Die 打印冲子
Manifold Block 歧管档块
Master Plate 靠模样板
Match Plate 分型板
Mold Base 塑胶模座
Mold Clamp 铸模紧固夹
Mold Platen 模用板
Moving Bolster 换模保持装置
Moving Bolster Plate 可动侧模板
One Piece Casting 整体铸件
Parallel Block 平行垫块
Parting Line 分模线
Parting Lock Set 合模定位器
Pass Guide 穴型导板
Peened Head Punch 镶入式冲头钻杆凸模Pilot Pin 定位销导向销子
Pin Gate 针尖浇口
Plate 衬板
Pre Extrusion Punch 顶挤冲头
Punch 冲头
Puncher 推杆
Pusher Pin 衬套梢
Rack 机架
Rapping Rod 起模杆
Re-entrant Mold 凹入模
Retainer Pin 嵌件梢
Retainer Plate 托料板
Return Pin 回位梢
Riding Stripper 浮动脱模器
Ring Gate 环型浇口
Roller 滚筒
Runner 流道
Runner Ejector Set 流道顶出器
Runner Lock Pin 流道拉梢
Screw Plug 头塞
Set Screw 固定螺丝
Shedder 脱模装置
Shim 分隔片
Shoe 模座之上下模板
Shoot 流道
Shoulder Bolt 肩部螺丝
Skeleton Frameworks 骨架
Slag Riser 冒渣口
Slide(Slide Core)滑块
Slip Joint 滑配接头
Spacer Block 间隔块
Spacer Ring 间隔环
Spider 模蕊支架
Spindle 主轴
Sprue 注道
Sprue Bushing 注道衬套
Sprue Bushing Guide 注道导套
Sprue Lock Bushing 注道定位衬套Sprue Puller 注道残料顶销浇道推出杆Sprue Line 合模线
Square Key 方键
Square Nut 方螺帽
Square Thread 方螺纹
Stop Collar 限位套
Stop Pin 止动梢
Stop Ring 止动环
Stopper 定位停止梢
Straight Pin 圆柱销
Stripper Bolt 脱料螺栓
Stripper Bushing 脱模衬套
Stripper Plate 剥料板
Stroke End Block 行程止梢
Submarine Gate 潜入式浇口
Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢
Supporting Plate 托板
Sweep Template 造模刮板
Tab Gate 辅助浇口
Taper Key 推拔键
Taper Pin 拔锥梢锥形梢
Teeming 浇注
Three Start Screw 三条螺纹
Thrust Pin 推力销
Tie Bar 拉杵
Tunnel Gate 隧道形浇口
Vent 通气孔
Wortle Plate 拉丝模板
Pierce 冲孔
Forming 成型(抽凸冲凸)
Draw Hole 抽孔
Bending 折弯
Trim 切边
Emboss 凸点
Dome 凸圆
Semi-Shearing 半剪
Stamp Mark 冲记号
Deburr or Coin 压毛边
Punch Riveting 冲压铆合
Side Stretch 侧冲压平
Reel Stretch 卷圆压平
Groove 压线
Blanking 下料
Stamp Letter 冲字(料号)Shearing 剪断
Tick-Mark Nearside 正面压印
Tick-Mark Farside 反面压印Extension Drawing 展开图procedure Drawing 工程图
Die Structure Drawing 模具结构图Material 材质
Material Thickness 料片厚度
Factor 系数
Upward 向上
Downward 向下
Press Specification 冲床规格
Die Height Range 适用模高
Die Height 闭模高度
Burr 毛边
Gap 间隙
Weight 重量
Total Weight 总重量
Punch Weight 上模重量Compression Molding 压缩成型
Flash Mold 溢流式模具
Extrusion Mold 挤压式模具
Split Mold 分割式模具
Cavity 型腔母模
Mold Core 模芯公模
Taper 锥拔
Leather Cloak 仿皮革
Shiver 饰纹
Flow Mark 流痕
Welding Mark 溶合痕
Post Screw Insert 螺纹套筒埋值Self Tapping Screw 自攻螺丝
Striper Plate 脱料板
Piston 活塞
Cylinder 汽缸套
Chip 细碎物
Handle Mold 手持式模具Encapsulation Molding 低压封装成型Two Plate 两极式(模具)
Well Type 蓄料井
Insulated Runner 绝缘浇道方式
Hot Runner 热浇道
Runner Plat 浇道模块
Valve Gate 阀门浇口
Band Heater 环带状的电热器
Spindle 阀针
Spear Head 刨尖头
Slag Well 冷料井
Cold Slag 冷料渣
Air Vent 排气道
Welding Line 熔合痕
Eject Pin 顶出针
Knock Pin 顶出销
Return Pin 回位销反顶针
Sleeve 套筒
Stripper Plate 脱料板
Insert Core 放置入子
Runner Stripper Plate 浇道脱料板Guide Pin 导销
Eject Rod (Bar)(成型机)顶业捧Subzero 深冷处理
Three Plate 三极式模具
Runner System 浇道系统
Stress Crack 应力电裂
Orientation 定向
Sprue Gate 射料浇口,直浇口
Nozzle 射嘴
Sprue Lock Pin 料头钩销(拉料杆)Slag Well 冷料井
Side Gate 侧浇口
Edge Gate 侧缘浇口
Tab Gate 搭接浇口
Film Gate 薄膜浇口
Flash Gate 闸门浇口
Slit Gate 缝隙浇口
Fan Gate 扇形浇口
Dish Gate 因盘形浇口
Diaphragm Gate 隔膜浇口
Ring Gate 环形浇口
Submarine Gate 潜入式浇口
Tunnel Gate 隧道式浇口
Pin Gate 针点浇口
Runnerless 无浇道
Sprueless 无射料管方式
Long Nozzle 延长喷嘴方式
Sprue 浇口溶渣
Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模
Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模
Loading Shoe Mold 料套式模具
Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具
Chill Mold 冷硬用铸模
Loose Mold 活动式模具
Cold Hobbing 冷挤压制模
Louvering Die 百叶窗冲切模Composite Dies 复合模具
Manifold Die 分歧管模具
Counter Punch 反凸模
Modular Mold 组合式模具
Double Stack Mold 双层模具
Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模
PCB 专业术语中英文翻译 很多PCB 的书上使用的是英文,但是大多数的人又看不懂英文, 这时候怎么办呢,我们需要翻译,但是如果每看到一个不会的词 儿就去翻译,那么就太耗费时间了,所以我们捷多邦总结了一些 常用的专业术语的中英文对照,希望能对大家有用。 1.印制电路:printed circuit 2.印制线路:printed wiring 3.印制板:printed board 4.印制板电路:printed circuit board (pcb) 5.印制线路板:printed wiring board(pwb) 6.印制元件:printed component 7.印制接点:printed contact 8.印制板装配:printed board assembly 9.板:board 1 10.表面层合电路板:surface laminar circuit (slc) 11.埋入凸块连印制板:b2it printed board 12.多层膜基板:multi-layered film substrate(mfs) 13.层间全内导通多层印制板:alivh multilayer printed board 14.载芯片板:chip on board (cob) 15.埋电阻板:buried resistance board 16.母板:mother board 17.单面印制板:single-sided printed board(ssb) 、管路敷设技术通过管线不仅可以解决吊顶层配置不规范高中资料试卷问题,而且可保障各类管路习题到位。在管路敷设过程中,要加强看护关于管路高中资料试卷连接管口处理高中资料试卷弯扁度固定盒位置保护层防腐跨接地线弯曲半径标等,要求技术交底。管线敷设技术中包含线槽、管架等多项方式,为解决高中语文电气课件中管壁薄、接口不严等问题,合理利用管线敷设技术。线缆敷设原则:在分线盒处,当不同电压回路交叉时,应采用金属隔板进行隔开处理;同一线槽内强电回路须同时切断习题电源,线缆敷设完毕,要进行检查和检测处理。、电气课件中调试对全部高中资料试卷电气设备,在安装过程中以及安装结束后进行 高中资料试卷调整试验;通电检查所有设备高中资料试卷相互作用与相互关系,根据生产工艺高中资料试卷要求,对电气设备进行空载与带负荷下高中资料试卷调控试验;对设备进行调整使其在正常工况下与过度工作下都可以正常工作;对于继电保护进行整核对定值,审核与校对图纸,编写复杂设备与装置高中资料试卷调试方案,编写重要设备高中资料试卷试验方案以及系统启动方案;对整套启动过程中高中资料试卷电气设备进行调试工作并且进行过关运行高中资料试卷技术指导。对于调试过程中高中资料试卷技术问题,作为调试人员,需要在事前掌握图纸资料、设备制造厂家出具高中资料试卷试验报告与相关技术资料,并且了解现场设备高中资料试卷布置情况与有关高中资料试卷电气系统接线等情况 ,然后根据规范与规程规定,制定设备调试高中资料试、电气设备调试高中资料试卷技术电力保护装置调试技术,电力保护高中资料试卷配置技术是指机组在进行继电保护高中资料试卷总体配置时,需要在最大限度内来确保机组高中资料试卷安全,并且尽可能地缩小故障高中资料试卷破坏范围,或者对某些异常高中资料试卷工况进行自动处理,尤其要避免错误高中资料试卷保护装置动作,并且拒绝动作,来避免不必要高中资料试卷突然停机。因此,电力高中资料试卷保护装置调试技术,要求电力保护装置做到准确灵活。对于差动保护装置高中资料试卷调试技术是指发电机一变压器组在发生内部故障时,需要进行外部电源高中资料试卷切除从而采用高中资料试卷主要保护装置。
模具英语专业术语 模具述语 一、入水:gate 进入位: gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口: switching runner/gate 唧嘴口径: sprue diameter 二、流道: runner 热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴: hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头: connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件: mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板: support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock 顶针: ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate 缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug
中英文对照外文翻译文献 (文档含英文原文和中文翻译) 外文: The development of plastic mould China's industrial plastic moulds from the start to now, after more than half a century, there has been great development, mold levels have been greatly enhanced. Mould has been at large can produce 48-inch big-screen color TV Molded Case injection mold, 6.5 kg capacity washing machine full of plastic molds, as well as the overall car bumpers and dashboards, and other plastic mould precision plastic molds, the camera is capable of producing plastic mould , multi-cavity mold small modulus gear and molding mold. --Such as Tianjin and Yantai days
Electrical Co., Ltd Polaris IK Co. manufactured multi-cavity mold VCD and DVD gear, the gear production of such size precision plastic parts, coaxial, beating requirements have reached a similar foreign the level of product, but also the application of the latest gear design software to correct contraction as a result of the molding profile error to the standard involute requirements. Production can only 0.08 mm thickness of a two-cavity mold and the air Cup difficulty of plastic doors and windows out of high modulus, and so on. Model cavity injection molding manufacturing accuracy of 0.02 to 0.05 mm, surface roughness Ra0.2 μ m, mold quality, and significantly increase life expectancy, non-hardening steel mould life up to 10~ 30 million, hardening steel form up to 50 ~ 10 million times, shorten the delivery time than before, but still higher than abroad,and the gap between a specific data table. Process, the multi-material plastic molding die, efficient multicolor injection mould, inserts exchange structure and core pulling Stripping the innovative design has also made great progress. Gas-assisted injection molding, the use of more mature technologies, such as Qingdao Hisense Co., Ltd., Tianjin factorycommunications and broadcasting companies, such as moldmanufacturers succeeded in 29 ~ 34-inch TV thick-walled shell, as well as some parts on the use of gas-assisted mould technology Some manufacturers also use the C-MOLD gas-assisted software and achieved better results. Prescott, such as Shanghai, such as the new
市场营销专业术语中英文对照标准翻译 本文为市场营销中经常用到的一些中文与英文互译的标准用语,希望对市场营销从业人员有所帮助。 《财富》杂志Fortune 案头调研Desk Research 奥美公司Ogilvy & Mather 白色商品White Goods 百乐门Parliament 百威啤酒Budweiser 包裹销售法Banded Pack 宝洁公司Procter & Gamble 宝丽来Polaroid 宝马BMW 边际成本Marginal Cost 边际收益Marginal Benefit 标准差,均差Standard Deviation 别克Buick 波立兹调查公司Alfred Politz Research, Inc 波旁王朝Ancient Age Bourbon 波特福洛分析Portefolio Analysis 产品差异Product Differentiation 产品生命周期Product Life Cycle 产品系列Product Line 产品组合Product Mix 阐述Presentation 超级市场Supermarket 成对比较法Paired Comparisons 成功的理想主义者Successful Idealist 承诺型消费者Committed Buyer 程度测试Tachistoscope 橙色商品Orange Goods 冲动购买Impulse Buying 重叠率Duplication 抽样Sampling 传销Pyramid Selling 传阅发行量Pass-on Circulation 词语联想法Word Associaton 刺激营销Incentive Marketing 促销Promotion 达彼思广告公司Ted Bates & Copany 大卫·奥格威David Ogilvy 戴比尔斯De Beers
如何用英文和老外检讨模具 (2008-1-16 08:50) 1.XXX!你现在有空吗,我可以问你一些问题吗? Could I ask you some questions?May I ask you some questions (a question)? 2.请问此产品的面是否为外观面?表面做什么处理?是晒纹/抛光? Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing? 3.请问产品这个面可否加顶针或顶块?产品允许加扁顶针吗? Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4.这个产品的柱位我们打算做司筒。(或镶针)可以吗? Can we add ejector sleeves or ejector pins in the boss of this part? 5.产品的这个位置有倒扣不能出模,我们打算做行位,在此面上会有分模线,你接受吗?There's an undercut at this position that can not be molded, we plan to make a slider for it. It will also have a parting line on this side, is that OK? 6.产品里面的这个位置我们打算做斜顶或内行位,有问题吗? We will make the lifter and (inner) slider in this position, will that be a problem? 7.你提供的2D产品图与3D产品图不一致,请问以哪一个图面为准? The 2D and 3D drawings you provided are not the same, could you advise which one is correct? 8.你提供的3D产品图有的地方没有出模角,有的地方胶位太厚,有的地方胶位太溥,这些产品问题我们可以自己修改吗?修改后会给交给你确认。 There is no draft angle in the 3D model, some areas are too thick, and some are too thin. Can we modify them by ourselves? We will send you the updated drawing for approval. 9.按你们提供的缩水率千分之五,这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确? According to the shrinkage rate .005”, the mold has been done in the right dimension, but the part falls short to your part print(the actual dimensions are out of tolerances), are you sure the shrinkage is right?
模具术语英文翻译
模具术语英文翻译 根据国家标准,以下为部分塑料模具成形术语的标准翻译。 动模 Movable Mould Moving Half 定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate 下模座板 Lower Clamping Plate 凹模固定板 Cavity-retainer Plate 型芯固定板 Mould Core-retainer Plate 凸模固定板 Punch-retainer Plate 模套 Die Body Die Sleeve Die Blank 支承板 Backing Plate Support Plate 垫块 Spacer Parallel 支架 Ejector Housing Mould Base Leg 模头 Die Head 根据国家标准,以下为部分压铸模具术语的标准翻译。 压力铸造模具 Die-Casting Die 压铸模零部件 定模 Fixed Die Cover Die 定模座板 Fixed Clamping Plate 定模套板 Bolster Fixed Die 动模 Moving Die Ejector Die 动模座板 Moving Clamping Plate 直流道 Sprue 横流道 Runner 内浇口 Gate 模具分类 Injection Mold 注塑模 Plastic Rubber Mould 塑胶模 Rubber Molding 橡胶成形 Hot Chamber Die Casting 热室压铸 Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模 Multi-Cavity Mold 多模穴模具 Stack Mold, Stack Injection Mould 叠层模
前言 在目前激烈的市场竞争中,产品投入市场的迟早往往是成败的关键。模具是高质量、高效率的产品生产工具,模具开发周期占整个产品开发周期的主要部分。因此客户对模具开发周期要求越来越短,不少客户把模具的交货期放在第一位置,然后才是质量和价格。因此,如何在保证质量、控制成本的前提下加工模具是值得认真考虑的问题。模具加工工艺是一项先进的制造工艺,已成为重要发展方向,在航空航天、汽车、机械等各行业得到越来越广泛的应用。模具加工技术,可以提高制造业的综合效益和竞争力。研究和建立模具工艺数据库,为生产企业提供迫切需要的高速切削加工数据,对推广高速切削加工技术具有非常重要的意义。本文的主要目标就是构建一个冲压模具工艺过程,将模具制造企业在实际生产中结合刀具、工件、机床与企业自身的实际情况积累得高速切削加工实例、工艺参数和经验等数据有选择地存储到高速切削数据库中,不但可以节省大量的人力、物力、财力,而且可以指导高速加工生产实践,达到提高加工效率,降低刀具费用,获得更高的经济效益。 1.冲压的概念、特点及应用 冲压是利用安装在冲压设备(主要是压力机)上的模具对材料施加压力,使其产生分离或塑性变形,从而获得所需零件(俗称冲压或冲压件)的一种压力加工方法。冲压通常是在常温下对材料进行冷变形加工,且主要采用板料来加工成所需零件,所以也叫冷冲压或板料冲压。冲压是材料压力加工或塑性加工的主要方法之一,隶属于材料成型工程术。 冲压所使用的模具称为冲压模具,简称冲模。冲模是将材料(金属或非金属)批量加工成所需冲件的专用工具。冲模在冲压中至关重要,没有符合要求的冲模,批量冲压生产就难以进行;没有先进的冲模,先进的冲压工艺就无法实现。冲压工艺与模具、冲压设备和冲压材料构成冲压加工的三要素,只有它们相互结合才能得出冲压件。 与机械加工及塑性加工的其它方法相比,冲压加工无论在技术方面还是经济方面都具有许多独特的优点,主要表现如下; (1) 冲压加工的生产效率高,且操作方便,易于实现机械化与自动化。这是
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边:guide pin 顶针板:ejector retainer plate 托板:support plate
预约券reservation ticket 下午茶high tea 微博Microblog/ Tweets 裸婚naked wedding 亚健康sub-health 平角裤boxers 愤青young cynic 灵魂伴侣soul mate 小白脸toy boy 精神出轨soul infidelity 人肉搜索flesh search 剩女3S lady(single,seventies,stuck)/left girls 山寨copycat 异地恋long-distance relationship 性感妈妈yummy mummy 钻石王老五diamond bachelor 时尚达人fashion icon 上相的,上镜头的photogenic 学术界academic circle 哈证族certificate maniac 偶像派idol type 住房公积金housing funds 熟女cougar(源自电影Cougar Club) 挑食者picky-eater 伪球迷fake fans 紧身服straitjacket 团购group buying 奉子成婚shotgun marriage 婚前性行为premarital sex 炫富flaunt wealth 决堤breaching of the dike 上市list share 赌球soccer gambling 桑拿天sauna weather 自杀Dutch act 假发票fake invoice 金砖四国BRIC countries 笑料laughing stock 泰国香米Thai fragrant rice 学历造假fabricate academic credentials 泄洪release flood waters 狂热的gaga eg: I was gaga over his deep blue eyes when I first set eyes on him 防暑降温补贴high temperature subsidy 暗淡前景bleak prospects
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机(尼龙拉勾)n yl on latch lock 45斜顶lifter 46模胚(架)mold base 47母模cavity in sert 48公模core insert 49行位(滑块)slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
Mold design and manufacture The mold is the manufacturing industry important craft foundation, in our country, the mold manufacture belongs to the special purpose equipment manufacturing industry. China although very already starts to make the mold and the use mold, but long-term has not formed the industry. Straight stabs 0 centuries 80's later periods, the Chinese mold industry only then drives into the development speedway. Recent years, not only the state-owned mold enterprise had the very big development, the three investments enterprise, the villages and towns (individual) the mold enterprise's development also quite rapid . Although the Chinese mold industrial development rapid, but compares with the demand, obviously falls short of demand, its main gap concentrates precisely to, large-scale, is complex, the long life mold domain. As a result of in aspect and so on mold precision, life, manufacture cycle and productivity, China and the international average horizontal and the developed country still had a bigger disparity, therefore, needed massively to import the mold every year . The Chinese mold industry except must continue to sharpen the productivity, from now on will have emphatically to the profession internal structure adjustment and the state-of-art enhancement. The structure adjustment aspect, mainly is the enterprise structure to the specialized adjustment, the product structure to center the upscale mold development, to the import and export structure improvement, center the upscale automobile cover mold forming analysis and the structure improvement, the multi-purpose compound mold and the compound processing and the laser technology in the mold design manufacture application, the high-speed cutting, the superfinishing and polished the technology, the information direction develops .
1. The undercut area where interfere with slide block need to be filled material to help the slide can move smoothly.(和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動) 2. The thickening added too thick.(加肉太多) 3. The thickening area is too wide.(加肉面積太大) 4. Gate position is moved.(GATE位置移位) 5. The split line of slide block or the area of slide.(滑塊拆的位置) 6. This area is hard to be filled due to the sharp feature(此處有尖角,填充困難) 7. The strength of this area is too weak and isn’t easy to get c old due to the steel too thin. 8. ( 此處鋼材太薄,強度不足而且不容易冷卻) 9. .The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark. 10. ( 圓柱特徵要有一半圓不可以拆在滑塊上,以免粘滑塊造成拉白,拉斷.) 11. The part will be damaged if we make lifter in this area. 12. ( 此處做斜銷在作動時會削到成品肉厚) 13. This is critical surface where is not allow to add material. 14. ( 這個面是裝配面,不能加料) 15. This thick wall area might because sink mark,Please reduce some wall thickness to improve it.) 16. ( 此處料位太厚,會有縮水,建議減料改善) 17. Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area. 18. (此面是不是外觀面,此處做滑塊的話會有結合線,是否可以接受) 19. Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on core and cavity side. No slide block and lifter to be made. 20. (此處有倒勾,能否減料,使公母模靠破,不做滑塊和斜銷) 21. Please confirm the issues of Parting line, Gate position...Etc otherwise the lead-time will be extended. 22. (請盡快確認這種拆模方式和結構,否則會影響模期) 23. The trim mark of the gate is not visual after open the top case if the gate position is design ed like it 24. (GATE做在此處的話.蓋子打開後看不到GATE的修剪部位) 25. We would suggest to enlarging draft to help tool released.) 26. 加大拔模角,以便脫模順利) 27. There are sharp edges if set the parting line at here, It will reduce the tool life 28. (P.L面開在此處,模具上會有尖角和刀口,對模具壽命有影響) 29. If you insist that the gate position have to be as original design then we would
根据国家规范,以下为部分塑料模具成形术语的规范翻译。 动模Movable Mould Moving Half 定模座板Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板Upper Clamping Plate 下模座板Lower Clamping Plate 凹模固定板Cavity-retainer Plate 型芯固定板Mould Core-retainer Plate 凸模固定板Punch-retainer Plate模套Die Body Die Sleeve Die Blank支承板Backing Plate Support Plate 垫块Spacer Parallel 支架Ejector Housing Mould Base Leg模头Die Head 模具分类8 Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成 形 Hot Chamber Die Casting 热室压铸Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具 Palletizing Die 叠层模Plaster Mold 石膏 模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模 Forming Die 成型模Progressive Die 连续模 Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模 Riveting Die 铆合模Compression Molding 压缩成型Flash Mold 溢流式模具 Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔母模Mold Core 模芯公模Large Die Mold 大型模具Precise Die Mold 精密模具 Complex Die Mold 复杂模具Foaming Mould 发泡模具 Metal Die 金属模具Plastic Mold 塑料模具Tool Stamping Die Punch Die 冲压模具 Extrusion Die 挤压模具Graphite Die 石墨模具流道浇口部分Runner System 浇道系统Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆 Runner Design 流道设计Main Runner 主流道 Secondary Runner 次流道Mould Gate Design 浇口设 计 Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口 Side Gate 侧浇口Edge Gate 侧缘浇口 Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口 Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口 Ring Gate 环形浇口Runnerless 无浇道 Sprueless 无射料管方式Long Nozzle 延长喷嘴方式 Sprue 浇口,溶渣Insulated/ Hot Runner 热浇 道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣 Sprue Gate 射料浇口Nozzle 射嘴 Sprue Lock Pin 料头钩销(拉料杆)注塑缺陷Flash 飞边Warpage 翘曲Air Trap 积风Blush 发赤Flow Line 流痕Splay 银纹Short Shot 短射Sink Mark 缩痕Streak 条纹Void 缩孔Weld Line 熔接线 Gas Mark 烧焦Cold Slug 冷斑Delamination 起皮Burr 毛刺Flaw Scratch 刮伤Gloss 光泽 Glazing 光滑Surface Check 表面裂痕Hesitation 迟滞注塑工艺Molding Conditions 成型条件Drying 烘干Barrel Temperature 料筒温度Melt Temperature 熔化温度 Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压Injection Speed 注塑速度Screw Speed 螺杆转速Tensile Strength 抗拉强度T ensile Elongation 延伸率Flexural Modulus 弯曲模Flexural Strength 抗弯强度Shrinkage 收缩率Regrind Usage 次料使用Moulding 模塑机械设备 Lathe 车床Planer 刨床Miller / Milling Machine 铣床Grinder 磨床Driller 钻床Linear Cutting 线切割Electrical Sparkle 电火花Welder 电焊机Punching Machine 冲床Robot 机械手Common Equipment 常用设备EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床Die