模具英语专业术语
模具英语专业术语模具的分类:
冲压模(五金模): stamping die
分离模: cutting die
成形模: forming die
塑胶模: plastics mold
注射模: injection mold
压缩模: compression mold
铸塑模: transfer mold
吹塑模: blow mold
吸塑模: suck mold
铸造模: casting die
砂型铸造: sand casting
压铸模: die casting
锻造模: forging die
塑胶模具术语
一、入水：gate
进入位(入水点)：gate location
水口形式：gate type
大水口(侧浇口): edge gate
潜水口: sub-gate
薄膜式水口: film gate
牛角式潜水口: banana gate
扇形水口: fan gate
环形水口: ring gate
二次水口:
细水口：pin-point gate
水口大小：gate size
转水口：switching runner/gate
唧嘴口径：sprue diameter
直接水口: direct gate
二、流道: runner
热流道：hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形(整圆/半圆)流道：round(full/half) runner
矩形流道: rectangle runner
梯形流道: trapezoid runner
U形流道: U shape runner
流道电脑分析(模流分析)：mold flow analysis
流道平衡: runner balance
-
热嘴：hot sprue/tip
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头：connector plug
插座：connector socket
密封/封料：seal
三、运水：water line
喉塞：line plug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socket
四、模具零件：mold components
三板模(细水口模)：3-plate mold
二板模(大水口模)：2-plate mold
热流道模具: hot-runner/manifold mold
叠层模: stacked mold
边钉/导边：leader pin/guide pin
边司/导套：guide pin/guide bushing
直导套：shoulder guide bushing
有托导套：straight guide bushing
中托司：ejector guide bush
中托边：ejector guide pin
回针: return pin
面板: top clamp plate
A板: A plate
推板：stripper plate
B板: B plate
托板：support plate
方铁: spacer block
加高方铁: higher spacer block
顶针固定板：ejector retainner plate
顶针板：ejector plate
底板: bottom clamp plate
螺丝：screw
杯头螺丝: socket cup head screw
平头螺丝: socket flat head screw
机米螺丝:
外六角头螺丝: bolt
栓打螺丝(等高螺丝)：S.H.S.B
管钉：dowel pin
开模槽：ply bar socket
内模管位(模仁互锁)：core/cavity inter-lock
顶针：ejector pin
-
司筒：ejector sleeve
司筒针：sleeve ejector pin
缩呵：movable core,return core, core puller
扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter
模胚（架）：mold base
上内模：cavity insert
下内模：core insert
行位（滑块）：slide
行位扣:
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wear plate
压条：gib
撑头: support pillar
唧嘴：sprue bushing
挡板：stop plate
定位圈(法兰)：locating ring
锁扣(模锁)：latch
扣鸡：parting lock set
推杆：push bar
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
型腔(前模仁): cavity
型芯(后模仁): core
镶针：insert pin
销子(销钉)：dowel pin
波子弹弓：ball catch
喉塞(堵头): pipe plug
锁模块：lock plate
斜顶杆：angle ejector rod
斜顶针：angle from pin
尼龙拉勾：parting locks
活动臂：lever arm
复位键、提前回杆：early return bar
气阀：valves
斜导边(斜导柱)：angle pin
油缸: hydraulic cylinder
-
液压马达: hydraulic motor
齿轮: gear
轴承: bear
术语：terms
承压平面平衡：parting surface support balance
分模面排气：parting line venting
回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水：water line interferes with ejector pin
料位出上/下模：part from cavity (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件：Do not use (core/cavity) insert
用铍铜做镶件：use beryllium copper insert
初步模图设计：preliminary mold design
正式模图设计：final mold design
反呵：reverse core
弹弓压缩量：spring compressed length
稳定性好：good stability,stable
强度不够：insufficient rigidity
均匀冷却：even cooling
扣模(粘模)：sticking
顶白: stress mark
热膨胀：thero expansion
缩水: shrinkage
物料表: BOM
原料: raw materials
物料: materials
工程试模材料: material for engineering mold testing
成品: finished product
半成品: semi-finished product
公差：tolorance
铜公(电极)：copper electrode
射料不足: short shot
缺口: nick
瑕疪(斑点): speck
亮斑: shine
银纹: splay
焦痕: gas mark
起鳞: delamination
冷块: cold slug
导色: blush
沟槽;凿槽: gouge
段面咬花: satin texture
-
证示线: witness line
专利: patent
沙砾: grit
细粒: granule=peuet=grain
抽粒机: grit maker
缓冲: cushion
不锈钢: stainless steel
镁铝合金: magnalium
镁金属: magnesium
钣金: metal plate
车/车床: lathe
铣床/铣床: mill
刨/刨床: plane
磨/磨床: grind
钻/钻床: drill
镗: boring
气泡: blinster
版次: revision
备注: remark
生产确认: production control confirmation
初审: checked by
核准: approved by
部门: department
电镀: plate
成型: molding
样品: sample
雕刻: engrave
蚀纹: texture
加硬: harden
热处理: heat treatment
淬火: quenching
回火: tempering
退火: annealing
碳化: carbonization
铬酸处理: chromate
阳性处理: anodize
氮化: nitrifying