[策划书]模具英语专业术语

[策划书]模具英语专业术语

模具英语专业术语

模具的分类:

冲压模(五金模): stamping die

分离模: cutting die

成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold

铸造模: casting die 砂型铸造: sand casting 压铸模: die casting

锻造模: forging die 塑胶模具术语

gate 一、入水:

进入位(入水点): gate location 水口形式: gate type

大水口(侧浇口): edge gate 潜水口: sub-gate

薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate

二次水口:

细水口: pin-point gate 水口大小: gate size

转水口: switching runner/gate 唧嘴口径: sprue diameter 直接水口: direct gate

二、流道: runner

热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道: round(full/half) runner

矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析): mold flow analysis

流道平衡: runner balance

热嘴: hot sprue/tip

热流道板:hot manifold

发热管:cartridge heater

探针: thermocouples

插头: connector plug

插座: connector socket

密封/封料: seal

三、运水:water line

喉塞:line plug

喉管:tube

塑胶管:plastic tube

快速接头:jiffy quick connector plug/socket

四、模具零件:mold components 三板模(细水口模):3-plate mold 二板模(大水口模):2-plate mold 热流道模具: hot-runner/manifold mold 叠层模: stacked mold

边钉/导边:leader pin/guide pin 边司/导套:guide pin/guide bushing 直导套:shoulder guide bushing有托导套:straight guide bushing 中托司: ejector guide bush 中托边: ejector guide pin 回针: return pin 面板: top clamp plate

A板: A plate

推板:stripper plate

B板: B plate

托板: support plate

方铁: spacer block

加高方铁: higher spacer block 顶针固定板:ejector retainner plate 顶针板:ejector plate

底板: bottom clamp plate 螺丝: screw

杯头螺丝: socket cup head screw 平头螺丝: socket flat head screw 机米螺丝:

外六角头螺丝: bolt

栓打螺丝(等高螺丝):S.H.S.B

管钉:dowel pin

开模槽:ply bar socket

内模管位(模仁互锁):core/cavity inter-lock

顶针: ejector pin

司筒:ejector sleeve 司筒针:sleeve ejector pin 缩呵:movable

core,return core, core puller

扣机(尼龙拉勾):nylon latch lock

斜顶:lifter

模胚(架): mold base 上内模:cavity insert 下内模:core insert

行位(滑块): slide 行位扣:

镶件:insert

压座/斜鸡:wedge

耐磨板/油板: wear plate 压条:gib

撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate

定位圈(法兰):locating ring 锁扣(模锁):latch

扣鸡:parting lock set 推杆:push bar

顶板:eracuretun

活动臂:lever arm

分流锥:spure sperader 水口司:bush

垃圾钉:stop pin

隔片:buffle

弹弓柱:spring rod

弹弓:die spring 型腔(前模仁): cavity 型芯(后模仁): core

镶针:insert pin

销子(销钉):dowel pin

波子弹弓:ball catch

塞(堵头): pipe plug 喉

锁模块:lock plate

斜顶杆:angle ejector rod 斜顶针:angle from pin 尼龙拉勾:parting locks 活动臂:lever arm

复位键、提前回杆:early return bar

气阀:valves

斜导边(斜导柱):angle pin 油缸: hydraulic cylinder

液压马达: hydraulic motor

齿轮: gear

轴承: bear

术语:terms

承压平面平衡:parting surface support balance 分模面排气:parting line venting

回针碰料位:return pin and cavity interference 模总高超出啤机规

格:mold base shut hight 顶针碰运水:water line interferes with ejector pin

料位出上/下模:part from cavity (core) side 模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.

不准用镶件: Do not use (core/cavity) insert 用铍铜做镶件: use beryllium copper insert 初步模图设计:preliminary mold design 正式模图设计: final mold design

反呵:reverse core

弹弓压缩量:spring compressed length 稳定性好:good stability,stable 强度不够:insufficient rigidity

均匀冷却:even cooling

扣模(粘模):sticking

顶白: stress mark

热膨胀:thero expansion

缩水: shrinkage

物料表: BOM

原料: raw materials

物料: materials

工程试模材料: material for engineering mold testing 成品: finished product

半成品: semi-finished product

公差:tolorance

铜公(电极):copper electrode

射料不足: short shot

缺口: nick

瑕疪(斑点): speck

亮斑: shine

银纹: splay

焦痕: gas mark

起鳞: delamination

冷块: cold slug

导色: blush

沟槽;凿槽: gouge

段面咬花: satin texture

证示线: witness line 专利: patent

沙砾: grit

细粒: granule=peuet=grain

抽粒机: grit maker 缓冲: cushion

不锈钢: stainless steel 镁铝合金: magnalium 镁金属: magnesium 钣金: metal plate 车/车床: lathe

铣床/铣床: mill

刨/刨床: plane

磨/磨床: grind

钻/钻床: drill

镗: boring

气泡: blinster 版次: revision

备注: remark

生产确认: production control confirmation

初审: checked by 核准: approved by 部门: department 电镀: plate 成型: molding

样品: sample 雕刻: engrave 蚀纹: texture 加硬: harden 热处理: heat treatment 淬火: quenching 回火: tempering 退火: annealing 碳化: carbonization 铬酸处理: chromate 阳性处理: anodize

模具常用术语中英文对照

模芯 Parting Core 耐落胶 Teflon Paste 局部视图 Partial View 偏移量 Offset 冷料 Cold Slag 水塞 Water Line Plug 线切割 Wire 撬模脚 Ppy Slot 轮廓 Contour 重新加工 Reworked 螺纹孔Tapping Hole 配件 Components 连接件 Fittings 补偿 Compensation 斜针 Angle Pin 平面度 Parallel 接合 Engage 倒角Chamfer 替换镶件Interchangeable Mold Inserts 模胚 Mold Base 指定吨位的注塑机 Specific Press 热嘴Hotnozzle 水嘴接头 Water Fitting 火花机 Edm 螺纹 Eyebolt Thread 熔接线 Weildline 回针 Stop Pin 压机 Press 二级顶出针 Sub-Leaderd Pin 嗮纹 Texturing 镶件 Mold Insert 梯形 Trapezoid

加硬 Harden 凸缘、法兰 Flange 唧嘴 Sprue 方铁 Spacer Block 设计筒图 Design Preliminary 顶针板 Ejector Plate 名称块表 Title Block 顶针底板 Ejector Retainer Plate 版本标识 Revision Level 垫板 Retainer Plate 材料清单 Stock List 后模镶针 Core Pin 制模 Build Mold 垃圾钉 Stop Pin 手动滑块 Hand Slide 有托顶针 Shoulder Ejector Pin 漏水测试 Leak Test 顶针板导套Guided Ejection Bushing 流道排气 Runner Vents 针板导柱 Guided Ejection Leader Pin 抛光 Draw Polish 唧嘴 Sprue Bushing 侧抽芯 Slide Action 三板模延伸式唧嘴 Extension Noozzle Bulishing 加强筋 Reinforcing 水口板导套 Runner Stripper Pin 三角撑 Gusset 定位圈（法兰）Locating Ring 柱子 Bossed 管钉（定位销）Dowel Pin 出模斜度 Draft 管状管钉 Tubular Dowel

电力专业常用英语词汇()

网易电力专业英语词汇(较全) 1）元件设备 三绕组变压器：three-column transformer ThrClnTrans 双绕组变压器：double-column transformer DblClmnTrans 电容器：Capacitor 并联电容器：shunt capacitor 电抗器：Reactor 母线：Busbar 输电线：TransmissionLine 发电厂：power plant 断路器：Breaker 刀闸(隔离开关)：Isolator 分接头：tap 电动机：motor 2）状态参数 有功：active power 无功：reactive power 电流：current 容量：capacity 电压：voltage 档位：tap position 有功损耗：reactive loss 无功损耗：active loss 空载损耗：no-load loss 铁损：iron loss 铜损：copper loss 空载电流：no-load current 阻抗：impedance 正序阻抗：positive sequence impedance 负序阻抗：negative sequence impedance 零序阻抗：zero sequence impedance 无功负载：reactive load 或者QLoad 有功负载: active load PLoad 遥测：YC(telemetering) 遥信：YX 励磁电流(转子电流)：magnetizing current 定子：stator 功角：power-angle

上限:upper limit 下限：lower limit 并列的：apposable 高压: high voltage 低压：low voltage 中压：middle voltage 电力系统 power system 发电机 generator 励磁 excitation 励磁器 excitor 电压 voltage 电流 current 母线 bus 变压器 transformer 升压变压器 step-up transformer 高压侧 high side 输电系统 power transmission system 输电线 transmission line 固定串联电容补偿fixed series capacitor compensation 稳定 stability 电压稳定 voltage stability 功角稳定 angle stability 暂态稳定 transient stability 电厂 power plant 能量输送 power transfer 交流 AC 装机容量 installed capacity 电网 power system 落点 drop point 开关站 switch station 双回同杆并架 double-circuit lines on the same tower 变电站 transformer substation 补偿度 degree of compensation 高抗 high voltage shunt reactor 无功补偿 reactive power compensation 故障 fault 调节 regulation 裕度 magin 三相故障 three phase fault 故障切除时间 fault clearing time 极限切除时间 critical clearing time 切机 generator triping

制造业工厂常用英文与缩写词汇大全

一:常用術語 Hon Hai 鴻海 CMM Component module move 機動元件整合 CEM Contract Manu faction service 合約委托代工 IBSC Internet Business Solution Center 國際互聯網應用中心 PCEG Personal Computer Enclosure group 個人電腦外設事業群（FOXTEQ）CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鴻富錦事業群 SABG system assembly business group 系統組裝事業群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鴻準 Stamping tool shop I 沖模一廠 Stamping tool shop II 沖模二廠 Prototype workshop 樣品中心 Steel factory 裁剪廠 PCE molding tooling workshop PCE塑模廠 Hua Nan test and measurement center 華南檢測中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 鎂合金 Engineer standard 工標 Document center (database center)資料中心 Design Center 設計中心 Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練 proposal improvement/creative suggestion提案改善 Technological exchange and study 技術交流研習會 Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩 QCC Quality Control Circle 品質圈 PDCA Plan Do Check Action 計劃執行檢查總結 DCC delivery control center 交貨管制中心 3C Computer 電腦類產品 Consumer electronics 消費性電子產品 Communication 通訊類產品 Core value（核心价值） Love 愛心

汽车制造专业英语词汇大全

汽车制造专业英语词汇 大全 Document serial number【KKGB-LBS98YT-BS8CB-BSUT-BST108】

汽车专业词汇 Assembly line组装线 Layout布置图Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcode条码barcode scanner 条码扫描器 fuse together熔合 fuse machine热熔机repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect 外观检查 inner parts inspect内部检查 thumb screw大头 螺丝 lbs. inch镑、英 寸 EMI gasket导电条 front plate前板 rear plate 后板 chassis 基座 bezel panel面板 power button电源 按键 reset button重置 键 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑 胶件 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 personnel resource department 人力资源部 production department生产部 门 planning department企划部 QC Section品管科 stamping factory 冲压厂 painting factory 烤漆厂 molding factory 成型厂 common equipment 常用设备 uncoiler and straightener整平 机 punching machine 冲床 gripper机械手 hydraulic machine油压机 lathe车床 planer |'plein| 刨床 miller铣床 grinder磨床 linear cutting线 切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager 总经理 special assistant manager特助 factory director 厂长 department director部长

电力电子-专业词汇中英文对照

电力电子-专业词汇中英文对照（一） AbsorberCircuit 吸收电路 AC/ACFrequencyConverter 交交变频电路ACpowercontrol交流电力控制ACPowerController交流调功电路ACPowerElectronicSwitch交流电力电子开关AcVoltageController交流调压电路AsynchronousModulation异步调制BakerClampingCircuit贝克箝位电路 Bi-directionalTriodeThyristor双向晶闸管BipolarJunctionTransistor--BJT双极结型晶体管Boost-BuckChopper升降压斩波电路Boost Chopper升压斩波电路BoostConverter升压变换器BridgeReversibleChopper桥式可逆斩波电路BuckChopper降压斩波电路BuckConverter降压变换器Commutation 换流 Conduction Angle 导通角ConstantVoltageConstantFrequency--CVCF 恒压恒频

ContinuousConduction--CCM （电流）连续模式ControlCircuit 控制电路 CukCircuit CUK斩波电路CurrentReversible Chopper 电流可逆斩波电路CurrentSourceTypeInverter--CSTI 电流（源）型逆变电路Cycloconvertor 周波变流器 DC-AC-DC Converter 直交直电路 DCChopping 直流斩波 DCChoppingCircuit 直流斩波电路 DC-DCConverter 直流－直流变换器DeviceCommutation 器件换流DirectCurrentControl 直接电流控制DiscontinuousConductionmode （电流）断续模式displacementfactor 位移因数 distortionpower 畸变功率 doubleendconverter 双端电路 drivingcircuit 驱动电路 electricalisolation 电气隔离 fastactingfuse 快速熔断器 fastrecoverydiode 快恢复二极管fastrevcoveryepitaxialdiodes 快恢复外延二极管

机械制造工程专业英语词汇样本

Chapter One Mechanics Components 第一章机械构件 Lesson One 第一课齿轮 Words and Expressions 1.spur gear 直齿轮 2.thermal expansion 热膨胀 3.lubrication 润滑 4.backlash 倾向间隙 5.the pitch circles 节圆 6.space width 间隙宽度 7.instrument gear 仪表齿轮 8.the split gear 拼合齿轮 9.helical gear 斜齿轮 10.p itch-line velocities 节线速度 11.a n axial thrust 轴向推力 12.b lank 坯件 13.d ouble-helical gears 人字齿轮 14.n on-intersecting 不相交的 15.w orm gears 蜗轮蜗杆 16.b evel gears 伞齿轮 17.c rossed-axis 交叉轴 18.n ut 螺母 19.s crew 丝杠, 螺钉 20.l arge rations 大速比 21.p arallel-shaft gears 平行轴齿轮 22.s ingle-thread worms 单线蜗杆

23.l ead angles 导角 24.m ultiple-thread worms 多线蜗杆 25.h ypoid gear 偏轴伞齿轮 26.r olling Cones 滚锥 27.i nvolutes 渐开线 Lesson Two Rolling Guides and Bearings 第二课滚动导轨和轴承 Words and Expressions 1.rolling guides (rolling guideways) 滚动导轨 2.plain guides 普通导轨 3.a roller chain 滚柱链 4.cape 保持架 5.guide surfaces 导轨面 6.stiffness 刚性 7.load-carrying capacity 载荷能力 8.rolling-contact bearings 滚动轴承 9.ball bearing 球轴承 10.a n inner race 内座圈 11.a n outer race 外座圈 12.s eparator 隔离环 13.c urvature 曲率 14.n otch 凹槽 15.t hrust load 推力负载 16.a radial ball bearing 经向球轴承 17.s ections 断面

专业英语词汇

电力电子专业英语 1、元件设备 三绕组变压器：three-column transformer ThrCln Trans 双绕组变压器：double-column transformer DblCl mnTrans 电容器：Capacitor 并联电容器：shunt capacitor 电抗器：Reactor 母线：Bus bar 输电线：Transmission Line 发电厂：power plant 断路器：Breaker 刀闸(隔离开关)：Isolator

功角：power-angle 电压等级：voltage grade 空载损耗：no-load loss 铁损：iron loss 铜损：copper loss 空载电流：no-load current 阻抗：impedance 正序阻抗：positive sequence impedance 负序阻抗：negative sequence impedance 零序阻抗：zero sequence impedance 电阻：resistance 电抗：reactance 电导：conductance 电纳：susceptance 导纳：admittance

无功负载：reactive load 或者QLoad 有功负载: active load PLoad 遥测：YC(telemetering) 遥信：YX 励磁电流(转子电流)：magnetizing current 定子：stator 功角：power-angle 上限:upper limit 下限：lower limit 并列的：apposable 高压: high voltage 低压：low voltage 中压：middle voltage 电力系统 power system 发电机 generator

制造业常用英语词汇

制造业常用英语词汇 制造业常用英语词汇－－强烈推荐!!! 一、部门及职位名称 总经理办公室General manager’s office 模具部Tooling department 项目部Project department 品质部Quality department 计划部Plan department 制造部Manufacture department Keypad产品部Keypad department IMD 产品部IMD department 五金部Metal stamping department 设计科Design section 冲压车间Stamping workshop 电镀车间Plating workshop 物控科Production material control section 计划科Plan section 仓务科Warehouse section 商务科Business section 品质规划科quality plan section IQC科IQC section IPQC科IPQC section

OQC科OQC section 检测中心measurement center 项目规划科Project plan section 项目XX科Project section XX 试模科Mold test section 成本科Cost section 设备科Facility section 采购科Purchase section 综合办General affairs office 编程科Programming section 模具工程科Tooling engineering section 模具装配车间Mold assembly workshop 文控中心Document control center (DCC) 注塑车间Injection workshop 喷涂车间Spray painting workshop 装配车间Assembly workshop 总经理General manager (GM) 经理manager XX部门经理Manager of XX department 原料库Raw material warehouse 半成品库Semi-finished product warehouse 成品库Finished product warehouse

工厂术语 英语

CORPORATE COMMON ABBREVIATION 常用语缩写 1 Organization组织 1-1 HQ Head Quarter 总公司 1-2Chairmen主席 1-3Lite-On Group光宝集团 1-4 President 总裁 1-5Executive Vice President 常务副总裁 1-6Vice President副总裁 1-7HR Human Resource人力资源部 1-8FIN Finance 财务 1-9Sales 销售 1-10R&D Research & Developing 研发部 1-11QA 质量保证QA DQA CS 1-12MIS Management Information System资讯管理系统1-13Pur 采购Purchasing 1-14IMD Image management division 影像管理事业部 1-15ITS information technology system 计算机部 1-16QRA quality reliability assurance 品保部 1-17MFG manufacturing 制造部 1-18PMC production &material control 生(产)物(料)管(理) 1-19 PRO Procuremnet 采购开发部

1-20 PMO Plant Manager Office 厂长室 1-21 CEO Chief Executive Officer 执行总裁 2 Materials 材料 2-1PC Production Control 生产控制 2-1-1MPS Mass Production Schedule 量产计划 2-1-2FGI Finished goods Inventory 成品存货 2-1-3UTS Units To Stock存货单元 2-1-4WIP Working In Process Inventory在制品 2-1-5C/T Cycle Time 循环时间,瓶颈 2-1-6WD Working Days 工作天 2-1-7MTD Month To Days 月初到今日(例如总表整理) 2-1-8YTD Year To Days 年初到今日 2-1-9 SO Sales Order 销售单 2-1-10MO Manufacture Order 制造单 2-1-11 BTO Build To Order 订单生产 2-1-12 P/N part number 料号 2-1-13 FCST Forecast 预测计划 2-1-14 W/O Working Order 工单 2-1-15 P/O Purchasing Order 采购单 2-1-16 VDS Vendor Delivery Schedule 厂商送货进度表2-1-17 D/C Delivery Order 交货单 2-2 MC Material Control材料控制

模具英语专业术语

模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水：gate 进入位(入水点)：gate location 水口形式：gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 直接水口: direct gate 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道：round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析)：mold flow analysis 流道平衡: runner balance

电力系统_专业英语词汇

电力系统power system 发电机generator 励磁excitation 励磁器exciter电压voltage 电流current 升压变压器step-up transformer 母线bus 变压器transformer 空载损耗：no-load loss铁损：iron loss 铜损：copper loss 空载电流：no-load current无功损耗：reactive loss有功损耗：active loss 输电系统power transmission system 高压侧high side 输电线transmission line 高压: high voltage低压：low voltage 中压：middle voltage 功角稳定angle stability稳定stability 电压稳定voltage stability 暂态稳定transient stability 电厂power plant 能量输送power transfer 交流AC直流DC 电网power system 落点drop point 开关站switch station 调节regulation 高抗high voltage shunt reactor并列的：apposable 裕度margin 故障fault 三相故障three phase fault分接头：tap 切机generator triping 高顶值high limited value 静态static (state) 动态dynamic (state)自动电压调节器AVR Automatic voltage regulator 电抗reactance 电阻resistance 功角power angle 有功（功率）active power 电容器：Capacitor电抗器：Reactor 断路器：Breaker 电动机：motor 功率因数：power-factor 定子：stator 阻抗电压：阻抗：impedance功角：power-angle 电压等级：voltage grade 有功负载: active load/PLoad无功负载：reactive load档位：tap position 电阻：resistor电抗：reactance 电导：conductance 电纳：susceptance上限:upper limit 下限：lower limit 正序阻抗：positive sequence impedance负序阻抗：negative sequence impedance零序阻抗：zero sequence impedance 无功（功率）reactive power功率因数power factor 无功电流reactive current 斜率slope额定rating 变比ratio 参考值reference value电压互感器PT 分接头tap 仿真分析simulation analysis下降率droop rate 传递函数transfer function 框图block diagram受端receive-side 同步synchronization 保护断路器circuit breaker 摇摆swing 阻尼damping 无刷直流电机：Brushless DC motor 刀闸(隔离开关)：Isolator机端generator terminal 变电站transformer substation 永磁同步电机：Permanent-magnet Synchronism Motor 异步电机：Asynchronous Motor 三绕组变压器：three-column transformer ThrClnTrans 双绕组变压器：double-column transformer DblClmnTrans 固定串联电容补偿fixed series capacitor compensation 双回同杆并架double-circuit lines on the same tower 单机无穷大系统one machine - infinity bus system 励磁电流：magnetizing current 补偿度degree of compensation Electromagnetic fields 电磁场失去同步loss of synchronization 装机容量installed capacity无功补偿reactive power compensation故障切除时间fault clearing time 极限切除时间critical clearing time 强行励磁reinforced excitation 并联电容器：shunt capacitor < 下降特性droop characteristics 线路补偿器LDC(line drop compensation) 电机学Electrical Machinery 自动控制理论Automatic Control Theory电磁场Electromagnetic Field微机原理Principle of Microcomputer 电工学Electrotechnics Principle of circuits 电路原理Electrical Machinery 电机学 电力系统稳态分析Steady-State Analysis of Power System 电力系统暂态分析Transient-State Analysis of Power System 电力系统继电保护原理Principle of Electrical System’s Relay Protection 电力系统元件保护原理Protection Principle of Power Syste m’s Element

模具英语专业术语

模具（MOULD/MOLD，TOOL）： CAVITY：前模 CORE：后模（定模） DIMENSION：寸法 GATE：浇口/水口/入水口 PIN GATE：点水口/点浇入水 SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向 DRAFT ANGEL：脱模斜度 PARTING LINE/P。L：分模线 EJECT PIN/E。P：注塑顶针 BLAST/TEXTURE：喷啥，蚀纹 MIRROR FINISH：镜面（抛光）处理POLISH：抛光 EMD：放电加工 WELD：熔接加工（烧焊） LATHE：车床 MILLING CUTTER：铣刀 MILLING MACHINE：铣床 WIRE CUT：线切割 CNC：主加工中心 POWER DRILL：电钻 DRILLING：钻孔 FRITING：烧结 ANNEALING：淬火 注塑术语（INJECTION） SCREW：螺杆 WELD LINE：熔接线 SINK MARK：缩水 DRAG MARK：脱花 BURR：批锋 FLOW MARK：流纹 SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶 INJECTION CYCLE：成型周期

注塑英语 型厚大小 Thick size 锁模结构（机绞/直压） Mode locking structure(machine twists/straight pressure) 最大开模距离 The biggest die sinking is away from 动模板最大模具重量 Moves the template maximum mold weight 哥林柱间距 Elder brother forest column spacing 顶出形式（电动五点，油压五点，油压十三点） Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots) 顶出长度 Goes against the length 顶棍孔直径 Goes against the stick hole diameter 顶棍孔中心矩 Goes against the stick hole central moment 螺杆材质（合金） Screw rod material quality (alloy) 螺杆转速 Screw rod rotational speed 最大射出体积 Projects the volume most greatly 最大射出量 Projects the quantity most greatly 射出率 Ejection rate 每10mm射出量（理论） Each 10mm projects the quantity (theory) 射咀直径 Shoots ju the diameter 射咀R值 Shoots ju the R value 射咀空径 Shoots ju the spatial diameter 定位环直径 Locating ring diameter 溶胶能力 Sol ability 驱动方式（全自动/全液压）

电气工程专业英语词汇汇总(综合版)

电气工程师专业英语词汇汇总 10kV distribution substation 10kV配电所abrupt change of voltage 电压突变accumulation of electric energy 电能存储actuating coil 动作线圈adjustment diagram 调整图 alarm 报警 alarm signal 报警信号alternating light 变光灯 ammeter 电流表 apparent energy consumption unit 单位视在能耗 arc furnace 电弧炉 armature 电枢 arrester; lighting arrester; surge diverters 避雷器 automatic voltage regulator 电压自动调整器backlighting; background illumination 背景照明 battery box 电池箱 battery charger 电池充电器battery contactor 电池接触器battery fuse 电池保险丝battery resistor 电池电阻器 blow-out coil 磁吹线圈 boom 吊杆 bracket (OCS) 底座（接触网）； 支架；托架bracket for headspan wire 定位索底座bridge 电桥 brush 电刷 built-in wardrobe; built-in closet; closet 壁灯 bulb; light(lamp) bulb; electric bulb 灯泡 butterfly valve with electric actuator 电动蝶阀 button 电钮 cable and accessories 电缆及附件 cable armour 电缆铠装 cable bays 电缆电线间隔cable box 电缆箱 cable bracket; cable tray 电缆托架 cable continuity test 电路复测 cable differential protection 电缆差动保护

工厂专业英语术语

工厂专业英语术语 Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OO BA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板b arcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条 front plate前板rear plate后板chassis 基座bezel panel面板 power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource departmen t 人力资源部production department生产部门planning department企划部QC Secti on品管科 stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机 punching machine 冲床robot机械手hydraulic machine油压机 lathe车床planer |'plein?|刨床miller铣床grinder磨床 linear cutting线切割electrical sparkle电火花welder电焊机 staker=reviting machine铆合机position职务president董事长 general manager总经理special assistant manager特助 factory director厂长department director部长 deputy manager | =vice manager副理section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长line supervisor线长 assistant manager助理to move, to carry, to handle搬运 be put in storage入库pack packing包装to apply oil擦油 to file burr 锉毛刺final inspection终检to connect material接料 to reverse material 翻料wet station沾湿台Tiana天那水 cleaning cloth抹布to load material上料to unload material卸料 to return material/stock to退料scraped |'skr?pid|报废 scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕 defective upsiding down抽芽不良defective to staking铆合不良 embedded lump镶块feeding is not in place送料不到位 stamping-missing漏冲production capacity生产力 education and training教育与训练proposal improvement提案改善 spare parts=buffer备件forklift叉车trailer=long vehicle拖板车 compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thicknes s gauge厚薄规