3S10P电池规格书-中英文对照
SPECIFICATION
电池规格书
Type（类型）：Li-ion Battery（锂离子电池）Model（型号）：18650/11.1V/20000mAh
Customer Approval
客户确认
Checked By/Date 审核/日期Approved By/Date
批准/日期
Company Stamp
(公司印章)
Prepared By/Date 编制/日期Checked By/Date
审核/日期
Approved By/Date
批准/日期
Add: 3th Floor，B Building ,He Fu Qin Industrial Park,Dalang Street, Longhua, Shenzhen, China 地址：深圳市龙华新区大浪上横朗工业园路合富勤工业园B栋3楼
TEL:+86-755-61962399 FAX:+86-755-61962380
公司网址：https://www.sodocs.net/doc/7b1652683.html, https://www.sodocs.net/doc/7b1652683.html,
Amendment Records 修正记录
No. 序号Edition
(版本)
Description
（记述）
Prepared by
（编制）
Approved by
（批准）
Date
（日期）
1 A/0 First Edition
首次发行
2016-04-09
CONTENT（目录）
1、Application Scope/适用范围-----------------------------------------------------------------------------------------------------4
2、Battery Specification Amendment/ 电池规格书修订------------------------------------------------------------------------4
3、Battery Testing Conditions/ 电池测试条件------------------------------------------------------------------------------------4
4、Standard依据标准-----------------------------------------------------------------------------------------------------------------4
5、Production description产品描述-------------------------------------------------------------------------------------------------5
6、Specification 主要技术参数--------------------------------------------------------------------------------------------------6-7
7、Battery Pack Security Testing / 电池组安全性试验--------------------------------------------------------------------------7
8、Battery Pack Security Testing / 电池组安全性试验------------------------------------------------------------------------7-8
9、Main Specifications & Testing Methods of Protection Board /保护板主要参数及测试方法: -------------------------9
10、Schematic diagram/原理框图--------------------------------------------------------------------------------------------------10
11、Packaging Method（包装方式）----------------------------------------------------------------------------------------------11
12、Warranty / 保修期---------------------------------------------------------------------------------------------------------------12
13、Battery Cell Operation Notices / 电池操作注意事项----------------------------------------------------------------------12
14、Battery Shell Design Notices / 电池外壳设计注意事项-------------------------------------------------------------------12
15、Notice for Assembling Battery Pack/ 电池装配注意事项---------------------------------------------------------------- 13
16、Other Notices / 其它注意事项-------------------------------------------------------------------------------------------------14
17、Using Battery Notes /使用电池注意事项-------------------------------------------------------------------------------------15
18、Battery Storage Conditions / 电池的存---------------------------------------------------------------------------------------16
19、Other Chemical Reaction / 其它的化学反应--------------------------------------------------------------------------------16
20、Notes / 注释----------------------------------------------------------------------------------------------------------------------16
Any copies are invalid without our company's approval
本资料未经本公司批准自行影印，视为无效
1、Application Scope/适用范围
This product specification covers the requirements for the rechargeable lithium-ion battery pack with protection
circuit for detecting function of over-charge, over discharge and over-current manufactured and supplied by
Shenzhen BoDa Power Battery Technology Co., Ltd.
本规格书描述了由深圳市博大电源电池科技有限公司设计的可充电锂离子电池的规格技术参数，该参数包括过充电，过放电和过电流等功能参数。
2、Battery Specification Amendment/ 电池规格书修订
If the raw materials, production processing, production system or battery usage environments & other
conditions need to be changed, the amendment side needs provide the written advice to the other side, only the both sides come to agreement, the amendment will be effective.
如果原材料、生产过程、生产系统或电池使用环境及要求发生改变，提出更改方须将改变的信息以书面形式通知对方取得供需双方同意后再行修订。
3、Battery Testing Conditions/ 电池测试条件
Shenzhen BoDa Power Battery Technology Co., Ltd made this specification for the lithium-ion rechargeable battery produced by us, in order to avoiding errors caused by different testing methods and conditions.
对深圳市博大电源电池科技有限公司生产的可充电锂离子二次电池产品的规格、测试方法进行规范，避免因测试条件、方法的不同引起误差。
3.1 Standard Test Conditions /标准测试条件
Test should be conducted with new batteries within one week after shipment from our factory and the cells shall
not be cycled more than five times before the test. Unless otherwise specified, testing and measurement shall be done under temperature of 20±5℃ and relative humidity of 45~75%.
测试必须使用出厂时间不超过一个星期的新电池，且未进行过五次以上的充放电循环。除非特别说明，否则测试需要在温度20±5℃，相对湿度45~75%的条件下进行。
3.2 Measuring Instrument and Apparatus/ 测量器具及设备
3.2.1 Dimension Measuring Instrument/ 尺寸测量器具
The dimension measurement shall be implemented by instruments with equal or more precision scale of 0.01mm.
尺寸测量器具的精度等级应不小于0.01 mm 。
3.2.2 Voltmeter（伏特计）
Standard class specified in the national standard or more sensitive class having inner impedance more than 10kΩ/V
按照国家标准指定规格等级或采用灵敏度更高的，测量电压时内阻不应小于10kΩ/V。
3.2.3 Ammeter（安培计）
Standard class specified in the national standard or more sensitive class.
Total external resistance including ammeter and wire is less than 0.01Ω.
按照国家标准指定规格等级或采用灵敏度更高的，包括电流表及电线在内的总外阻应小于0.01Ω。
3.2.4 Impedance Meter（电阻计）
Impedance shall be measured by a sinusoidal alternating current method(1kHz LCR meter).
内阻测试仪测量原理应为交流阻抗法（1kHz LCR）。
4、Standard依据标准
This product complies with National Standard GB/T18287-2000“Cell Phone Lithium-ion Battery
General Specifications” of PRC.
本产品依据标准：中华人民共和国国家标准 GB/T 18287-2000《蜂窝电话用锂离子电池总规范》。
5、Production description产品描述
5.1 Name名称：锂离子电池
5.2 Mode型号：18650/3S10P/20000mAh/11.1V 5.3 Cell 电芯：18650 /2000mAh/3.7V
5.4 Shelf period 保质期限：1年
5.5 Structure Drawing电池结构图：(mm)
Dimension 外形尺寸
Length：长度MAX: 200±1mm
Vernier caliper
游标卡尺Width：宽度MAX:185±1mm
Thick：厚度MAX:22±1mm
wire length：线长180mm+5mm
6、 Specification 主要技术参数
7、Battery Pack Reliability Testing / 电池组可靠性试验
7. 1 Testing Condition (Unless Special Requirements) 测试条件（除非特别规定）
Atmosphere Pressure ： 86~106kPa 大气压力： 86~106kPa
All testing under full capacity （12.60-13.05V ） 测试项目在充满电状态下进行（12.60-13.05V ） 7.2 Reliability Test/电池组可靠性试验
NO 序号
Items 项目 Parameter 参数 Remarks 备注 6.1
Rated Capacity 标称容量 20000mAh Discharge:0.2C
放电
cut-off voltage:9.0V
截止电压
Minimum Capacity
最小容量 19800mAh 6.2 Energy 能量 222Wh 6.3 Nominal V oltage
标称电压
11.1V 6.4 Open V oltage 出厂电压 10.8V~12.0V
6.5
Load Voltage 负载电压 ≥10.8V 10?出厂电压条件 6.6
Internal Impedance 内阻
Charge voltage 充电电压 ≤280m?
12.6V AC 1KHz after standard
charge
标准充电后 AC 1KHz
测试
6.7 Standard charge current
标准充电电流 5000mA 6.8 Max charge current 最大充电电流 8000mA 6.9 Standard discharge current
标准放电电流 5000mA 6.10 Max discharge current 最大放电电流 8000mA 6.11 Discharge cut-off voltage
放电截止电压 9.0V 0~+45℃ Charge 充电 6.12
Operating Temperature
工作温度 -20~+60℃ Discharge 放电 6.13
Storage Temperature
贮存温度
-20℃～+60℃ Less than 1 month 小于一个月 20℃～+30℃ Less than 6 months 小于六个月
6.14 Weight 重量
About g
No. 序号Item
项目
Testing Conditions and Method
测试方法及条件
Standard
标准
1 Free Fall Testing
自由跌落试验
Fall the battery freely from a height of 1m (minimum
height) onto an 18mm thickness board placed on the cement
floor. The test is to be carried out on six directions (±x, y, z
axes).
将充满电的电池PACK从1.0m的高度上跌落到放置在水
泥地面上的18mm厚的硬木板上，每面跌落1次，6个面
都要跌落。
The appearance of battery should
not leakage, break or explosion
电池外观不开裂，电性能正常。
内部电芯不破裂、不起火；
固定可靠。
2 Vibration Testing
振动试验
Fix a charged battery on a vibrating table, vibrate it for 90
minutes in three mutually perpendicular directions at the
0.8mm resonance. The frequency is to be varied at the rate
of 1Hz/min between 10 and 55 hertz.
将充满电的电池固定在振动平台上，在三个相互垂直的
方向按振幅0.8mm的谐振形式进行振动, 频率在
10-55HZ以1Hz/min的速率变化，往复振动30分钟。
The appearance of battery should
not leakage, break or explosion
电池外观不开裂，电性能正常。
内部电芯不破裂、不起火；
固定可靠。
3
High
Temperature
高温性能
A charged battery is placed in an oven for 2 hours at
55±2oC, then discharged at a 0.5C current to the termination
voltage.
在55±2oC条件下，将标准充电后的电芯放入高温箱中
2h 后，再以1C 电流放电至终止电压。
Discharge 85 percent of the
original capacity.
可放出初始容85%.
4 Low Temperature
低温性能
A charged battery is placed in a thermal chamber for 2 hours
at -10oC±2oC; then discharged at 0.1C to the termination
voltage.
在-10±2oC条件下，将标准充电后的电芯放入低温箱中
2h后，再以0.2C 电流放电至终止电压。
Discharge more than 70 percent
of the original capacity.
可放出初始容量的
70% （-10 oC）以上.
5
Constant
Humidity &
Temperature
Testing
恒定湿热试验
Place a full charged battery under the environments of 40 oC
and 90% - 95%RH for 48 hours. And keep it in the room
temperature for 2 hours. Then discharge it at the current of 1C
to the cut-off voltage.
将充满电的电池在40 oC、相对湿度90%~95%的环境中放置
48小时后，在室温20±5 oC放置2小时。以1C电流放电到
电池不能放电.
The battery should be no
remarkable breakage, distortion.
Discharge time should not less
than 36mins
电池外观应无变形、爆裂，
放电时间应不低于36分钟。
6 High & Low
Temperature
Storage
高低温贮存
lace a full charged battery in a oven with 55±2 oC for
2 hours, then keep it under 20±5 oC for 4hrs, then place it in a
oven with -20±2 oC for 2 hours, then keep for 4 hours under
20±5 oC, cycle as high temperature-normal temperature-low
temperature-normal temperature-high temperature for 10 times
电池充满电后，将电池放入55±2 oC的高温箱中恒温2小时，再在
环境温度20±5 oC下放置4小时，然后放入-20±2 oC的低温箱中
恒温2小时，再在环境温度20±5 oC下放置4小时，继续按高温
—常温—低温—常温—高温循环10次。
The battery should be no
remarkable breakage, distortion.
And charge/discharge normally
电池外观无变形或爆裂现象，电池
充放电正常。
7
Humidity
and heat test
湿度和热度测试
A charged battery is placed in a box for 48 hours where the
temperature is 40±2oC and the relative humidity is 90%～
95% ；
将标准充电后的电芯放入温度为40±2 oC，相对湿度为
90%～95%的箱子中，保持48h。
No explosion,no fire
无爆炸、无起火
8 Cycle Life
循环寿命
Discharge it with the current of 0.5C to the cut-off voltage, and
store it for 15min.Charge a battery with the current of 0.5C ,
then keep the voltage and current constant and continue to
charge it until completed . After storing the battery for 15min.
The test is to be conducted as per the above cycles. The cycle
should be 500 times. At the 501 times discharge capacity should
not be less than 2.08Ah with 0.5C
以0.5C电流恒流放电至电池不能放电止，再以标准电流将其
充电到规定限制电压，静止15分钟，以0.5C电流恒流放电
至电池不能放电止，放电结束后，静止15分钟，再进行下次
充放电循环，直至500次循环。第501次电池以0.5C电流恒
流放电容量≥2.08Ah。
Discharge Capacity
≥2.08Ah
放电容量≥2.08Ah
9 Heat shock
热冲击
The cell is placed in a thermal chamber. Temperature is raised to
120±2oC at the rate of (5±2oC)/min and held for 10 minutes, then
cooled to room temperature at the rate of 5±2oC/min.
电池置于热箱中，温度以（5±2度）/min的速率升至120±2度并
保温10min,再以5±2度/min的速度降至室温。
No explosion,no fire
无爆炸、无起火
10 Charge Retention
电荷保持能力
At 20±5℃ completely charge and store it for 28days, and then
discharge it with 0.5C to the cut-off voltage.
完全充电后在环境温度为20±5℃的条件下，储存28天，然后
进行0.5C恒流放电至电池不能放电止。
remain capacity
≥2.21Ah
剩余容量≥2.21Ah
8、Battery Pack Security Testing / 电池组安全性试验
No. 序号Item
项目
Testing Conditions and Methods
测试方法及条件
Standard
标准
1 Over-charge
过充电
After standard charging, the cell is conducted for 8 hours while the
constant voltage is held at \ and standard charging current flows No
explosion, no fire through it.
将标准充电后的电芯，用恒定电压/和标准充电电流给电芯进
行加压8h。
No explosion, no fire
无爆炸、无起火
2 Over-Discharge
Protection Test
过放保护试验
Discharge the battery at the rate of 0.2C with the load of 30Ω for
24h .Charging for 10sec with specified adapter , and check the
voltage(≥9.0V)
将充满电的电池，以0.2C放电至电池不能放电后，外接30Ω负载
放电24h。再对电池充电10秒钟，电压应该≥9.0V
No explosion, no fire
无爆炸、无起火
3 Short-circuit
短路
Use a resistor with 0.1Ω to make the battery short circuit for 1 hour.
The appearance and characteristics are normal。
将充满电的电池，用小于0.1Ω电阻器短路电池PACK输出端正负
极1h，电池外观和性能正常不变。
the battery should be no
remarkable breakage, distortion.
And charge normally。V oltage /
电池不爆炸、不起火。
外观正常，电压/。
4 Impact Test
冲击试验
Place a full charged battery on a flat and put a stainless steel stick
(Diameter 7.9mm) in the middle of the battery upright. Beat the
steel stick with 10Kg
将充满电的电池放置在一个平面上，用一个直径为7.9mm不锈
钢棒竖放在电池正中间，用一个10Kg的力作用在不锈钢棒上。
No explosion, no fire
无爆炸、无起火
9、Main Specifications & Testing Methods of Protection Board：
电池保护板主要参数、标准及测试方法:
9.1Testing Conditions测试条件：
Temperature：20±5℃温度：20±5℃
Relative Humidity：45~75% 相对湿度：45~75%
Atmosphere pressure：86~106kPa 大气压力：86~106kPa
9.2Main Specifications & Testing Methods of Protection Board保护板主要参数及测试方法：
NO 序号Item 项目Criteria 标准(单节)
1 Over-charge Protection V oltage
过充电保护电压
/
2 Over-discharge protection V oltage
过放保护电压
/
3 Over current protection current
放电过流保护电流
/
4 Current consumption in normal operation
工作时消耗电流
/
5 nner resistance
内阻
/
6 Start battery voltage balance
电池均衡启动电压
/
7 Battery current balance
电池均衡电流
/
11、Packaging Method（包装方式）Undetermined待定
12、Warranty / 保修期
The delivery period from battery date for 12 months If the battery is proved in manufacturing process defect formation rather than the user by use of abuse and error caused. Our company is responsible for replacement battery.
电池的保质期从出货之日算起为12个月。如果证明电池的缺陷是在制造过程中形成的而不是由于用户滥用及错误使用造成，本公司负责退换电池。
13、Battery Cell Operation Notices / 电池操作注意事项
13.1Prohibition short circuit/ 禁止电池短路
Never make short circuit cell. It generates very high current which causes heating of the cells
and may cause electrolyte leakage, gassing or explosion that are very dangerous. The LI tabs may be easily
short-circuited by putting them on conductive surface. Such outer short circuit may lead to heat generation
and damage of the cell. An appropriate circuitry with PCB shall be employed to protect accidental short circuit
of the battery pack.
避免电池短路。短路会产生很高的电流而使电池发热以及电解液泄漏，产生有毒气体或爆炸是非常危险的。
极片连接在导电物体表面很容易短路，外部短路会导致发热及损害电池。选用一个适当的保护电路可以在意外短路时保护电池。
13.2 Mechanical shock/ 机械撞击
Falling, hitting, bending, etc. may cause degradation of LI characteristics.
跌落、碰撞、弯曲等等都可能会降锂电池的性能。
13.3 Handling of tabs/ 极片操作注意事项
The battery tabs are not so stubborn especially for aluminum tab. Don't bend tab. Do not bend tabs unnecessarily.
极片的机械强度并非异常坚固，特别是铝片。没有必要时禁止弯折极片。
14. Battery Shell Design Notices / 电池外壳设计注意事项
14.1 Pack toughness/ 外壳坚韧度
Battery pack should have sufficient strength and the LI cell inside should be protected from mechanical shocks.
电池外壳应该有足够的机械强度使电池免受机械撞击。
14.2 Cell fixing/ 电池的固定
The LI cell should be fixed to the battery pack by its large surface area. No cell movement in the battery pack should be allowed.
电池最大面积的一面应该固定在外壳上，安装后电池不能有松动。
14.3 Inside design/ 外壳内部设计
No sharp edge components should be insides the pack containing the LI cell.
外壳内安装电池的部位不应有锋锐边。
14.4 For mishaps/ 针对意外事件
Battery pack should be designed not to generate heat even when leakage occurs due to mishaps.
1) Isolate PCB (Protection Circuit Module) from leaked electrolyte as perfectly as possible.
2) Avoid narrow spacing between bare circuit patterns with different voltage. (Including around connector)
3) LI battery should not have liquid from electrolyte, but in case If leaked electrolyte touch bare
circuit patterns, higher potential terminal material may dissolve and precipitate at the lower potential terminal, and may cause short circuit. The design of the PCB must have this covered.
发生意外时外壳设计应考虑即使在电池出现漏液时也不会发热。
1）尽量把保护电路与渗漏的电解液隔离开。
2）在不同的电压情况下避免出现小间距的裸露电路——包括插头周围。
3）电池不应该有来自电解液的液体，但是一但发生电解液渗漏触及裸露电路，高电势端接子材料可能会溶解然后沉淀到低电势端接子，可能会造成短路。保护板的设计必须含有覆盖保护层。
15、Notice for Assembling Battery Pack/ 电池装配注意事项
Shocks, high temperature, or contacts of sharp edge components should not be allowed in battery pack assembling process.
在电池装配过程中不允许撞击、高温或接触尖锐部分。
15.1 Cell connection
电芯的连接
Ultrasonic welding or spot welding is recommended for LI tab connection method.
Battery pack should be designed that shear force are not applied to the LI tabs.
If apply manual solder method to connect tab with PCM, below notice is very important to ensure battery performance: 1）he solder iron should be temperature controlled and ESD safe;
2）Soldering temperature should not exceed 350°C;
3）Soldering time should not be longer than 3s;
4）Soldering times should not exceed 5 times, Keep battery tab cold down before next time soldering;
5）Directly heat cell body is strictly prohibited, Battery may be damaged by heat above approx. 100°C
建议使用超声波或点焊焊接方法；外壳设计应使极片不受外力。
如果使用人工焊接保护板，下面的注意事项对于确保电池性能非常重要：
1）铬铁的温度必须可控且可防静电；
2）接时铬铁的温度不能超过350度；
3）焊锡时间不能超过3 秒钟；
4）焊锡次数不能超过5 次，待极片冷却后才能进行下一次焊锡；
5）严禁直接加热电芯，高于100度会损害电芯。
电芯的安装Cell installation
①The cell should be fixed to the battery pack by its large surface area.
② There should be no sharp edges at the assembly contact area.
③ Cells must be held firmly in the battery pack; movement is not allowed.
①应将电芯的宽面安装在外壳内；
②装电芯的位置不能有毛刺和尖锐边角；
③电芯不能在壳内活动。
15.2 Cell connection/ 电池连接
1) Direct soldering of wire leads or devices to the cell is strictly prohibited.
2) Lead tabs with pre-soldered wiring shall be spot welded to the cells.
Direct soldering may cause damage of components, such as separator and insulator, by heat generation.
1）严禁直接焊接引线或设备到电池上。
2）极片在焊接引线之前应该先点焊到电池上，直接与电池热焊接，产生的热量会使电池的隔离体及绝缘体受损。
15.3 Prevention of short circuit within a battery pack/ 电池内部的短路预防
Enough insulation layers between wiring and the cells shall be used to maintain extra safety protection. The battery
pack shall be structured with no short circuit within the battery pack, which may cause generation of smoke or firing.
在电池和引线之间应该有足够的绝缘层用于安全保护。电池的包装构成应没有导致起烟起火的短路情况。
16、Other Notices / 其它注意事项!
16.1 Prohibition of disassembly / 禁止拆卸
1) Never disassemble the cells
The disassembling may generate internal short circuit in the cell, which may cause gassing, firing, explosion,
or other problems.
2) Electrolyte is harmful
LI battery should not have liquid from electrolyte flowing, but in case the electrolyte come into contact with the skin, or eyes, physicians shall flush the electrolyte immediately with fresh water and medical advice is to be sought.
1）不要拆卸电池。
拆卸电池会发生电池内部短路，会引起起火、爆炸、有害气体或者其它问题。
2）电解液是有害的
万一电解液沾到皮肤、进入眼睛，应立即用清水冲洗以及求助医生。
16.2Prohibition of dumping of cells into fire/ 不要把电池倾倒于火中
Never incinerate nor dispose the cells in fire. These may cause explosion of the cells, which is very dangerous and is prohibited.
不要焚毁电池，否则会致电池爆炸，这个很危险，必须禁止。
16.3Prohibition of cells immersion into liquid such as water / 禁止浸泡电池
The cells shall never be soaked with liquids such as water, seawater, drinks such as soft drinks, juices, coffee or others.
请不要把电池浸泡在液体当中，像清水、海水，及非酒精饮料、果汁、咖啡或者其它的饮料。
16.4Battery cells replacement/ 更换电池
The battery replacement shall be done only by either cells supplier or device supplier and never be done by the user.
更换电池应由电池生产商或设备供应商完成，用户不要自行更换。
16.5 Prohibition of use of damaged cells/ 禁止使用损坏的电池
The cells might be damaged during shipping by shock. If any abnormal features of the cells are found such as
damages in a plastic envelop of the cell, deformation of the cell package, smelling of an electrolyte, an
electrolyte leakage and others, the cells shall never be used any more.
The Cells with a smell of the electrolyte or a leakage shall be placed away from fire to avoid firing or explosion.
电池可能在出货途中碰撞而受损。如果发现电池有异常，例如包装损坏、电池包裹变形，有电解液的味道、发现漏液等等，不要再使用这些电池。电池如果有电解液的味道或者出现漏液，电池放置应该远离火源避免起火及爆炸。
17、Using Battery Notes /使用电池注意事项
17.1 Handling of cells:
★Don't charge the cells and keep them in a charged state for a long time.( Display units should dismantle the battery) ★Avoid any short-circuit. It will cause the leads to get hot and lose electronic functions.
★Soft package is easily damaged by sharp objects such as needles and knives. Avoid
touching the cells with sharp objects when handling and storing.
★Next to the leads is the sealed edge. Don't bend or fold the sealing edge as it is sensitive to movement.
★Don't open the folded edge on the sides of the cell.
★Don't bend the tabs as the tabs are sensitive.
★Avoid mechanical shock to the cells.
★Don't put the cells into an oven, washing machine or any high-voltage container.
★Don't use a charger without a safety certification. Use only a recommended charger.
★You should immediately stop charging if the cell overheats, emits an odor, changes color, changes shape, etc.
★Adults should supervise the use of batteries by children.
★Before using batteries, please carefully read and understand the handling guidelines.
★Avoid electro-static discharge when using, charging, and storing cells.
★Avoid putting the battery in contact with metal conductors such as neck chains, barrettes, or bolts, etc.
★Don't use metal conductors to connect the positive and negative leads together.
★Avoid errors during assembly by contacting the positive lead with the negative lead.
17.1使用电芯时应注意：
★电池不能长时间充电，不能长期处于充电状态。（如展示品需拆下电池）
★慎防短路，任何情况引起的短路可能会导致极耳金属发热，使电池功能失效。
★电芯属于软包装,包装材料易被尖锐物品刺伤,诸如尖针,刀片等, 电芯在使用和存放时应避免与尖锐物品碰撞。
★电芯极耳引出端为顶封边，顶封边为电芯密封敏感区，使用时，禁止弯折顶封边。
★禁止打开电芯两侧的折边。
★电芯极耳的机械强度并非异常坚固，禁止弯折极耳，特别是铝极耳。
★禁止机械撞击电芯、坠落、弯折电芯。
★不要把电池放在加热器皿、洗衣机或高压容器中。
★不要使用非指定的和没有安全认证的充电器给电池充电。
★在使用充电或储存期间如发现电池有变热、散发气味、变色、变形或其它反常之处应停止使用。
★把电池放到小孩够不到的地方以免吞服。
★儿童使用电池时，监护人应详细解释操作方法。
★在使用电池之前，应详细阅读操作指南并对使用中的注意事项有足够深刻的理解。
★电池应在远离静电的场所进行充电、使用和储存。
★不要在火源附近或温度超过60度的轿车中使用或遗留电池，也不要在这些环境中进行充放电。
★不要把电池同项链发夹硬币或螺钉等金属品一起放在手提包中，也不要把电池同上述物品一起储存。
★不要使用金属导体短路电池的正、负极。
★在使用时应注意电池的正、负极不要反装。
★不要使用带有严重变形的电池。
18、Battery Storage Conditions / 电池的存放
The batteries should be stored at room temperature, charged to about 30% to 50% of capacity. We recommend
that batteries be charged about once per half 3 months to prevent over discharge.
电池应当在室温下存放，应充到30%至50%的电量。如长时间储存，建议每三个月充一次电以防止电池过放电。
19、Other Chemical Reaction / 其它的化学反应
Because batteries utilize a chemical reaction, battery performance will deteriorate over time even if stored for
a long period of time without being used. In addition, if the various usage conditions such as charge, discharge,
ambient temperature, etc. are not maintained within the specified ranges the life expectancy of the battery may be
shortened or the device in which the battery is used may be damaged by electrolyte leakage. If the batteries cannot
maintain a charge for long periods of time, even when they are charged correctly, this may indicate it is time to change the battery.
由于电池是利用化学反应的原理，所以随时间的增加电池的性能会降低，即使是存放很长一段时间而不使用。
如果使用条件如充电、放电及周围环境温度等情形不在指定的使用范围内，会使缩短电池的使用寿命，或者会产生漏液导致设备损坏。如果电池长周期不能充电，即使充电方法正确，这样需要更换电池了。
20、Notes / 注释:
Any other items which are not covered in this specification shall be agreed by both parties.
本规格书未包括事项应由双方协议确定。
锂电池规格书
储能型磷酸铁锂电池规格书STORAGE LiFePO4 BATTERY SPECIFICATIONS 客户名称(Customer)： 产品型号(Type)： CF12V80Ah 发行日期(Issuing Date)：
1. 适用范围(Product Scope) 本规格书描述了锂离子二次电池的技术要求、测量方法、运输、储存及注意事项。 This Specification describes the requirements of the lithium ion rechargeable battery supplied by 2. 电池组特性 (Battery Group Specifications)
单只电芯曲线图feature curve for single cell 3. 技术要求(Technical Requirements) 测试条件(除特别规定) Testing Conditions (unless otherwise specified) 温度Temperature: 15~35℃ 相对湿度Relative Humidity: 45%~75% 大气压Atmospheric pressure: 86~106Kpa 充放电性能 (Electrical Characteristics)
环境性能 (Environmental Characteristic) 机械性能(Mechanical characteristics)
安全性能(Safe Characteristic)
4 电池组基本性能 (Basic Characteristics of Battery) 5 电池组保护功能要求 (Battery Required Protection Functions) To insure the safety, charger and the protection circuit shall be satisfied the items below. As safety device, please use in combination with the temperature fuse. The standard charge method is CC/CV (constant current/constant voltage) 为确保安全,充电器和保护电路应符合以下要求。同时请使用装有热熔保险丝的安全装置。标准充电方法为CC/CV(恒流/恒压)
技术规格书(中英文)
NPC-National Petro Co. 3600t Revolving/Engineering Crane Technical Specification (Project Plan) Shanghai Zhenhua Port Machinery (Group) Co., Ltd. 2005-12-10 Table of Content
1.1 General Description 总则 1.1.1Consist of the Specification 本规格书组成 The specification including general, hull structure, outfitting, machinery, electrical, refrigerating, air conditioning, ventilating, pipelaying, DP, and crane parts describes the 3600t CRANE PIPELAYING VESSEL based on scheme design. 本规格书由船舶总体、舾装、轮机、电气、通风冷藏空调、动力定位、起重机及铺管设备估价等部分组成，表述3600 t全回转起重工程船的主要技术规格方案。 1.1.2Construction Explanation建造说明 The BUILDER’s supply covers the item described in this specification, anything excluding from the scope of the specification will be supplied by the OWNER. 本船的建造估价，所有规格书所规定的项目均由建造方提供。超过规格书部分船东提供。 1.1.3Language and Measuring Unit文种与计量单位 The drawings, instructions, instruments, display, caution sign and nameplate shall be written in English and kept down the foreign nameplate of the importation of machine and equipments. Metric system is used for designing and fabricating of hull, crane and equipment etc. unless otherwise specialized in specification or instruction. 本船的图纸、使用说明书、仪表、显示、警示牌和铭牌等均以英文书写。进口机械、设备保留原来外文铭牌。 船体、起重机、机电设备等设计和建造，除非在规格书或说明书中特别表明，均采用公制计量单位。 1.2General Description船舶航区及用途 1.2.1The Sailing Area and Functions船舶航区及用途 The vessel is designed as a large-scale all revolving self-propelled vessel. The vessel is used for offshore projects. 本船是一艘自航大型全回转起重工程船，航行于无限航区。 本船主要用于海上海洋工程等作业。 1.2.2Type of Vessel船型 The vessel will be a steel, all welded crane ship with streamline bow, round bilge and bilge keel. A helicopter platform will be situated at forecastle deck. One (1) full revolving crane to be installed in the after area of deck. The vessel will be equipped with two (2) 2000kW tunnel thrusters at bow, two (2) 2500kW retractable azimuthing thrusters at the foreship, two (2) 4500kW azimuthing thrusters at the aftship. The dynamic positioning system is GL DYNPOS–AUTR class. 本船是一艘钢质、全电焊起重工程船。设流线型首，尾部纵向及舭部有圆角，设舭龙骨。船首设居住区及直升飞机起降平台。 船尾设置一台全回转吊机。 首部设2台轴隧式侧推装置，功率2×2000kW；设2台伸缩式全回转螺旋桨推进器，功
锂电池规格书参照
聚合物锂离子电池 产品规格承认书 ：：JD220768430F（500Ah） 品名： 品名 编制审核批准 客户确认 签名//日期客户名称//印章签名 客户名称 总部：北京神州巨电新能源技术开发有限公司 Beijing Globe Super Power New Energy Technology Development Corp. 地址：中国北京市海淀区上地3街9号嘉华大厦E座206 ADD:Rm E-206,Gem Tech-Center,No.9,3rd Street,Haidian Dist.,Beijing,P.R.China 86-10--82783543-816Fax:86-10 86-10--82780720-1073 Tel:86-10 工厂：河北神州巨电新能源科技开发有限公司 Hebei Globe Super Power New Energy Technology Development Corp. 地址：河北邢台市巨鹿县巨鹿工业园 Hebei i Province,P.R.China ADD:Industrial District,Ju Jul l u,Xiangtan,Hebe
产品规格承认书 目录 1.适用范围---------------------------------------------------------------------------------------------------------2 2.产品规格---------------------------------------------------------------------------------------------------2 3.电池性能检查测试-----------------------------------------------------------------------------------------2 4.外观尺寸图------------------------------------------------------------------------------------------------------3 5.使用指南--------------------------------------------------------------------------------------------------------3 6.其它事项------------------------------------------------------------------------------------------------------4 7.电芯处理须知---------------------------------------------------------------------------------------------------4
机械类常用技术要求中英文
常用技术要求 before the feeding control and the wind meets the tube welding, to the good center, in the hole guaranteed that ￠204 the pipeline can pass through. the 进料接管和出风接管焊前对好中心，内孔保证￠204管道能穿过。 welding uses the manual arc welding, welding rod trademark J420G. before the 焊接采用手工电弧焊，焊条牌号J420G。 painting, must carry on the superficial stain removal, the elimination welding residual and so on, its quality scale sees JB/T5000.12 the stipulation; Prime, in Huang He the blue color (according to color model) the polyurethane finishes two. Besides various laps spread the yellow paint, other spread the blue color. In the paint does not allow to contain the lead. Does not allow to have leaks flaws and so on paint, wrinkle paint. 涂装前要进行表面除锈、清除焊接残渣等，其质量等级见JB/T5000.12的规定；涂底漆一层、中黄和中蓝色（按颜色样板）聚氨酯面漆二层。除各盖板涂中黄漆外，其余均涂蓝色。漆中不允许含铅。不允许有漏漆、皱漆等缺陷。 sealants and so on lap like seal lax available CH107, JLC-1 spread in the slit main point. on 盖板如密封不严可用CH107,JLC-1等密封胶涂在缝隙大处。
诺瓦科技LED接收卡MRV220-15规格书英文版
Specifications Receiving Card MRV220-15 Product images provided in this file are for reference only , and the actual products shall prevail. Rev1.0.1 NS110100270 X I ' A N N O V A S T A R T E C H C O ., L T D .
Features MRV220 is the receiving card of Nova with 28-group data mode. It has the following features: 1) Single card outputs 24-group of RGB data; 2) Single card outputs 28-group of RGB data; 3) Single card outputs64-group of serial data; 4) Single card support resolution 256x226; 5) Configuration fileread back; 6) Temperature monitoring; 7) Ethernet cable communication status detection; 8) Power supply voltage detection; 9) Pixel-by-pixel brightness and chromaticity calibration, Brightness and chromaticity calibration coefficients for each LED; 10) Supports dual power backup function: It supports two-way power detection and screen brightness will be adjusted automatically when power failure occurs in any way of the power. NOTE: PWR1_S and WR2_S default to normal. Power shall be guaranteed to be pulled down to GND after power failure occurs; 11) Comply with RoHS standard; 12) Comply with EU CE-EMC Class A standard. X I 'A N N O V A S T A R T E C H C O ., L T D .
锂电池规格书
1.概述 General 此型号2406S 155×90×50mm的铝质外壳充电器能在输出6A的情况下工作，具有反接保护功能。 Battery Charger 2406S 155×90×50mm can work normally under 6A and with reverse polarity protection. 2.主要参数 Main product specification
3.环境条件 Environmental condition 4.技术特征 Electrical characteristics 输入特征： Input characteristic 输出特征和充电模式： Output characteristic or charge stages 保护特征： Protection characteristics
充电指示 Charging indicator 5.安全性 Safety & EMC
备注：辨识A：在技术要求范围内，充电器功能正常； Remark: Discrimination A- Function OK under technical requirement range; 辨识R：只有由外部干扰信号引起的保护装置（保险丝）损坏，整个设备在更换保护装置和重设运行参数后才能正常工作，因机械性损坏和设备故障的设备却不能。 Discrimination R- Physical damage or failure of equipment are not allowed, but damage of protection device (fuse) caused by interference signal of outside is allowed, and the whole equipment can work normally after replacement of protection device and reset of running parameter 6.环境测试要求 Environmental testing requirements 7.机械特征
锂电池规格书
充电器规格书 Specification of Battery Charger 型号:ES2406S 6A 锂电池充电器 （全铝外壳） / 6A Li Iron/Li Polymer BATTERY CHARGER 1.概述 General 此型号2406S 155×90×50mm的铝质外壳充电器能在输出6A的情况下工作，具有反接保护功能。 Battery Charger 2406S 155×90×50mm can work normally under 6A and with reverse polarity protection. 2.主要参数
Main product specification 3.环境条件 Environmental condition 4.技术特征 Electrical characteristics 输入特征： Input characteristic 输出特征和充电模式：
Output characteristic or charge stages 保护特征： Protection characteristics
充电指示 Charging indicator 5.安全性 Safety & EMC
备注：辨识A：在技术要求范围内，充电器功能正常； Remark: Discrimination A- Function OK under technical requirement range; 辨识R：只有由外部干扰信号引起的保护装置（保险丝）损坏，整个设备在更换保护装置和重设运行参数后才能正常工作，因机械性损坏和设备故障的设备却不能。 Discrimination R- Physical damage or failure of equipment are not allowed, but damage of protection device (fuse) caused by interference signal of outside is allowed, and the whole equipment can work normally after replacement of protection device and reset of running parameter 6.环境测试要求 Environmental testing requirements
诺瓦科技LED控制器MCTRL600规格书英文版
Specifications Independent Controller MCTRL600 V2.1.0 NS110100121 X i ’a n N o v a S t a r T e c h C o ., L t d .
Overview MCTRL600 is an advanced model of Nova controllers, which supports extra-large resolution. With HDMI/DVI video input and four Ethernet port outputs, a single unit is able to load 2560×960. Multiple units can be cascaded for uniform control. Feature 1) HDMI/DVI input; 2) HDMI/external audio input; 3) 12bit/10bit/8bit HD video source; 4) Resolution supported: 2048×1152，1920×1200，2560×960; 5) Resolution supported: 1440×900 (12bit/10bit); 6) 1 light sensor interface; 7) Cascading supported; 8) 18bit gray scale processing and presentation; 9) Video format: RGB, YCrCb4:2:2, YCrCb4:4:4; 10) Standard 1U housing and independent power supply. X i ’a n N o v a S t a r T e c h C o ., L t d .
技术规格书模板
技术规格书模板 -标准化文件发布号：（9456-EUATWK-MWUB-WUNN-INNUL-DDQTY-KII
中国石油大庆炼化公司 技术规格书 （物资名称：） 编制人：（专业厂或业务管理部门签字）年月日审核人：（专业厂单位领导签字）年月日 审批人：（业务管理部门领导签字）年月日
目录 1.总则 2. 执行标准 3. 主要技术要求 4. 检验和试验 5. 包装及运输 6. 资料交付 7. 技术服务及售后保证 8. 其它 附件供货范围 1．总则
1.1 本技术规格书适用于大庆炼化公司物资招标，提出了该物资生产、检验、试验、验收、运输、试用和售后服务等方面的基本技术要求； 1.2 投标人所供物资的材料、制造、检验和试验，按标准的最新版本要求执行；其它未列出的与本产品有关的规范与标准，投标人有义务在投标文件中列出。投标人应对所供产品质量承担全部责任。 1.3 在所有技术文件中的文字和计量单位，采用中文（中英文对照）和国际SI单位。 1.4 投标人所采用的专利涉及到的全部费用均被认为已经包含在报价中，投标人承担所提供的设计、制造过程中所涉及的各类专利技术的法律责任。投标人保证所采用技术不侵犯 任何第三方权益，如引发知识产权方面相关的法律纠纷，由投标人负全责。 2. 执行标准： 标准名称：下列标准或规范应为国家标准、行业标准或集团公司标准（不能为供应商企业标准）。 例：GB/T 14976 液体输送用不锈钢无缝钢管 GB/T 14975 结构用不锈钢无缝钢管 ………… 3. 主要技术要求（如有） 针对于标的物的具体要求，在本条列出。 例如具体参数要求，形式形状要求，特殊材质要求等。 4. 检验和试验（如有） 有标准的执行标准 例：执行GB/T 14976检验标准） 4.1 生产过程检验要求（如有） 例：需提供生产过程检验报告 4.2 出厂检验要求（如有） 例：需提供出厂合格证 4.3 第三方检验要求（如有） 例：需提供省级以上质量监督部门检测机构报告 4.4 购买招标文件后递交投标样品要求、试验要求（如有） 填写详细的递交样品方式、数量、包装、检验流程、报告出具等详细要求。 例：需提供样品一份。0.5L瓶装，开标前送至招标管理中心负责人处。 4.5 到货验收要求（如有）
电池规格书模板
TEL:( 0752)3535208 FAX:( 0752)3761580 Date：2017-3-30 Specification Approval Sheet 产品规格承认书 Customer 客户名称：域拓 Model产品型号：4L Type 产品类型：Li-ion battery Specification产品规格：3.7V/1400mAH signed by client 客户签名 Confirmed确认： Checked 审核： Approved 批准： signed by manufacturer 生产商签名 Prepared 制定：肖泽建 Checked 审核： Approved 批准：丁明谊 AMENDMENT RECORDS
TEL:( 0752)3535208 FAX:( 0752)3761580 Date：2017-3-30 Modification Time Description Issued Date Approved By 0 New release2015-06-26
TEL:( 0752)3535208 FAX:( 0752)3761580 Date：2017-3-30 Catalogue 目录 1 .Battery type and scope电池型号和适用范围 (4) 1 . 1: model产品型号： (4) 1 . 2: scope适用范围：客户定义 (4) 2 . Basic character and compose of battery电池的基本特性及组成 (4) 2 . 1: fundamental performance parameter of battery电池基本性能参数： (4) 2 . 2: Main components and parts主要零部件 (6) 2 . 3: Regular performance and unfailing performance产品常规性能和可靠性能 (6) 2 . 4: Contour Dimension of the Battery电池外形尺寸 (11) 3 . Specifications of Parts零部件规格 (112) 3 . 1: fender保护板 (122) 3 . 2: general electric and protection characters一般电气与保护特征 (122) 3 . 2: electric schematic diagram of battery电池电路原理图： (133) 3 . 3 : PCB layout 电路布局图………………………………………………………………….错误！未定义书签。3 4 . Specifications of the Cells电芯规格 (144) Announcements注意事项 (155) Danger 危险 (155) Warnings 警告 (166) Announcements 注意事项 (167)
技术规格书
技术规格书 产品名：氢热分析仪系统 数量：1套 1.概要 主要用于测定无机气体的升温脱离分析装置，对升温过程中，从钢材中所逃逸的氢含量进行高精密度定量分析，可为高强度钢以及大型锻件焊接组织的氢脆敏感性以及储氢合金的分析评价提供重要分析数据。 2.系统构成 （１）分析室 （２）样品加热室 （３）样品导入室 （４）排气控制系统（包括烘烤系统） （５）氢含量数据采集系统 3.主要技术规格 3.1分析室 ·检出器：四重极质谱仪 质量测量范围：1~100amu 质量分析精度：0.01ppm wt以下(5g试样中） ·排气性能： 氢背景值：5×10-9Pa以下（产品保证值·、包括样品加热炉心管） 真空泵：两段涡轮分子泵（320L/s磁悬浮型涡轮分子泵，50L/s涡轮分子泵）机械泵 ·可烘烤温度：200℃（带烘烤保护罩） ·真空脱气处理：450℃/10h以上超高真空脱气处理（出場付真空脱气处理 分析数据） ·真空计：UHV規格电离真空计 ·隔离装置：与样品加热室采用全金属超高真空闸阀隔离 ·氢气校正
标准4点氢气校正：4.99×10-6atm?cc/sec 2.0×10-5atm?cc/sec 5.0×10-5atm?cc/sec 1.0×10-4atm?cc/sec 可实施至1.0×10-4atm?cc/sec＝1atm的氢气校正，高精度（±0.5%）绝对压力计裝備，可对应规定压力值准确填充校正氢气。 填充氢气前实施真空排气，绝对压力计的原点复位每次校正。 氢气填充后，可通过开启阀门操作在超高真空下将标准校正氢气导入至炉心管。整个校正步骤，包括真空排气，2点校正线生成，氢气填充操作以及校正后的预备排气使用提示画面功能执行自动操作。 3.2样品加热室 ·加热方式：外加热式3区高温电气炉（管式） ·炉心管体：石英（超高真空金属法兰焊接规格，氢背景值5×10-9Pa） ·样品导入：磁耦合样品传输，无需使用样品架，低放出气体规格 ·可加热样品尺寸：φ20mm×50mm以下(形状不限） ·最高加热温度：Max.1000℃（均热长200mmm/±5℃） ·升溫速度：50℃/h~600℃/h任意可调，可设定保溫时间 溫度经时数据以及升溫結束信号输出功能 3.3样品导入室 ·排气性能：大气压~超高真空（5×10-5Pa）只需15分 ·真空泵：涡轮分子泵，辅助机械泵 ·可烘烤溫度:150℃ ·真空计:超高真空电离真空计 ·隔离装置:与样品加热室采用超高真空全金属闸阀隔离 3.4排气控制系统 ·触摸式PLC自动控制 分析室，样品导入室的真空排气/停止自动操作 样品交换时的真空排气以及阀门自动操作
锂电池规格书
储能型磷酸铁锂电池规格书 STORAGE LiFePO4 BATTERY SPECIFICATIONS 客户名称(Customer)： 产品型号(Type)： CF12V80Ah 发行日期(Issuing Date)： 1. 适用范围(Product Scope) 本规格书描述了锂离子二次电池的技术要求、测量方法、运输、储存及注意事项。 This Specification describes the requirements of the lithium ion rechargeable battery supplied by Prepared 制定 Checked 审核 Approved 批准
2. 电池组特性(Battery Group Specifications) Cell 电芯 Model规格型号IFP8081230-10Ah Capacity容量10 Ah Rated Voltage 标称电压 3.2 V Internal Resistance 内阻标准≤4 mΩ Combination Standard配组标准 A. 容差Capacity Difference≤1% B. 内阻Resistance()=1～2 mΩ C. 荷电保持能力Current-maintaining Ability≥90% D. 电压Voltage3.3～3.4V Combination Method组合方式4串8并4S 8P Pile Index 成品参数 Rated Capacity 标称容量80.0Ah Minimal Capacity最小容量（0.3C5A）80.0Ah Nominal Voltage额定电压12.0V Max. Charge Voltage 最大充电电压14.8 V Discharge cut-off voltage放电截止电压10.0V Charge Current充电电流5-10A Working Current工作电流10-20A Output and Inpu t输出端与输入端P+(red) / P-(black) Weight电池重量9.2Kg Dimension外形尺寸（L×W×H）168×260×132mm(不包含外露开关) Charge Method 适用充电 Standard标准5A×16hrs Quick快速20A×4hrs. Operating Temperature 适用温度 Charge充电0℃～45℃；32o F～113o F Discharge放电-20℃～60℃；-4o F～149o F
QX7137英文版规格书
Typical Application R CS 1 V IN V IN (a)Low V oltage Application (b) High V oltage Application Figure 1：Typical Application Circuit Diagrams of QX7137 General Description QX7137 is a constant current regulator for LED driver with low quiescent current and low dropout voltage. The LED current ranges from 100mA to 3.0A. In addition to LEDs, QX7137 also needs the external connection of a NMOS and a resistor to set the LED current. QX7137 uses SOT23-5 package Features Power Supply Voltage: 2.7~5.5V Extremely Low Quiescent Current: 26uA Sink Current: 100mA~3.0A Current Accuracy: ±5% Extensible Power Supply: Above 400V Extensible LED Current: Up to 3.0A Applications Power LED Driver
Ordering Information Type Number QX7137 Package Marking 7137X Lot Number Pin Assignments SOT23-5 7137X GND CS VDD DRV EN 1325 4
电子产品中英文规格书完整版
Page 1 Of 12 ShenZhen C&D Electronics CO.Ltd. Add: Building 2, X iayousong Mountaintop Industrial District,Yousong Village,LongHua T own, Baoan District ShenZhen China Zip 518109 Tel: 86-755- 28142422 Fax: 86-755-28142699 E-mail: export@https://www.sodocs.net/doc/7b1652683.html, Remote control specification (Rev. A0) Seller Customer Part Name :Remote control Part No. : Part Name : Part No. : Seller approval Customer approval Prepared By: Date:Received by: Date： Checked By: Date: Checked by: Date: Approved By: Date:Approved by: Date: company chop：company chop： Change history Version Date Description Author Page 2 Of 12 2、目录Index
NO. appellation Page 1 规格书封面(Approval Sheet Cover) 1/12 2 目录(Index) 2/12 3 检验内容及要求(Verification content & Requirement) 3/12～6/12 4 码表(Code table) 7/12 5 产品效果图(Product Cosmetics drawing) 8/12 6 原理图(Schematic diagram) 9/12 7 爆炸图(Explosion drawing) 10/12 8 产品尺寸图(Dimension drawing) 11/12 9 包装尺寸图(Packaging drawing) 12/12
磷酸铁锂电池 18650-1500-3.2V中文规格书 蒋合你好
产品规格书 产品名称：锂离子电池 产品型号：HTCF18650-1500mAh-3.2V 制订:周会 审核:李涛 批准:
目录 1. 适用范围 (3) 2. 型号 (3) 3. 外观及尺寸 (3) 4. 主要技术参数 (3) 5. 性能曲线 (4) 6. 安全性能 (5) 7. 环境适应性能 (6) 8. 标准测试环境 (6) 9. 储存及其它事项 (6) 10. 电池使用操作注意事项 (6)
1. 适用范围 本产品规格书描述了海特电子集团有限公司（以下简称海特电子）生产的锂离子电池产品性能指标。 2. 型号 HTCF18650-1500mAh-3.2V 3. 外观及尺寸 项目尺寸(mm) 直径（Ф）18.2±0.1 高度（H）64.8±0.4 4. 主要技术参数 序号项目标准 备注 1 标称容量1500mAh 0.5C，（本型号1C电流值为1500mA） 2 容量范围1450~1550mAh 0.5C 3 标称电压 3.2 V 4 交流内阻≤60mΩ加PTC型 5 充电 条件 截止电压 3.65±0.05V 以0.5C恒流充电至3.65V，恒压充电至电 流降至0.01C截止截止电流0.01C 6 放电截至电压 2.5V 7 循环性能2000次1C充电/1C放电，容量保持率≥80%，100%DOD 8 最大持续放电电流 4.5A 9 脉冲放电电流10A，5s 10 工作温度充电：0°C ~ 55°C；放电：-20°C ~ 60°C 11 储存温度-20°C ~ 45°C 12 电池重量42g (约)
5. 性能曲线 18650-1500mAh-3.2V电池0.5C充放电曲线 2 2.22.42.62.83 3.23.43.63.80 200 400 600 800 1000 1200 1400 1600 1800 容量/mAh 电压/V 充电放电 18650-1500mAh-3.2V 不同倍率放电曲线 2 2.32.62.9 3.23.53.80 200 400 600 800 10001200140016001800 容量/mAh 电压/V 0.1C 0.2C 0.5C 1C 2C 3C 18650-1500mAh-3.2V 不同温度放电曲线（0.5C） 1 1.52 2.53 3.540 300 600 9001200 1500 1800 容量/mAh 电压/V 60℃30℃10℃0℃-10℃-20℃-40℃
诺瓦科技LED视频处理器VX6s规格书英文版
VX6s All-in-One Video Controller Document Version: V1.0.0 Document Number: NS160100264 Specifications X I 'A N N O V A S T A R T E C H C O ., L T D .
Copyright ? 2018 Xi’an NovaStar Tech Co., Ltd. All Rights Reserved. No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means without the prior written consent of Xi’an NovaStar Tech Co., Ltd. Trademark is a trademark of X i’an NovaStar Tech Co., Ltd. Statement You are welcome to use the product of Xi’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar). This document is intended to help you understand and use the product. For accuracy and reliability, NovaStar may make improvements and/or changes to this document at any time and without notice. Any problem in use or any good suggestion, please contact us through ways provided in the document. We will do our utmost to solve the problems and adopt the suggestions after evaluation as soon as possible. Website: www.novastar.tech X I 'A N N O V A S T A R T E C H C O .,L T D .
产品规格书模版
Shenzhenleyondoptoelectronicsco.,ltd 深圳市立洋光电子有限公司 SPECIFICATION (产品规格书) PARTNO. :LY-WH61L0BLIJ05 (产品型号) SPECNO. :LY-LEYOND-052404 (规格书编号) DESCRIPTION :50瓦白光大功率LED (产品描述) DATE :24/05/2012 R&DDEPARTMENT (技术部) APPROVED (核准) CHECKED (审核) PREPARED (制定) 刘春香 工厂地址：深圳市宝安区石岩镇水田村同富康工业区B栋5楼深圳OFFICE：深圳市福田区华强北路华强广场一楼Q1A224号/ 邮箱： 香港立洋电子有限公司 地址：香港九龙旺角弥敦道555号九龙行11楼1102-1103室 PartNO.:LY-WH61L0BLIJ05 SPECNO.:LY-LEYOND-052404 REVNO.:A1
■Description (描述) ◆PartNO.(产品型号)：LY-WH61L0BLIJ05 ◆LEDChip：Material(材质)，InGaN/GaN、EmittedColor(发光颜色)，Blue(蓝色) ◆LEDEmittedColor(LED发光颜色)：White(白色) ◆LensColor(透镜颜色)：Clear(透明) ■Feature (特性) ◆50WHighPowerLED(50W大功率LED) ◆Package:SMTPackage(贴片式外形) ◆HalfAngle(2Θ1/2):120°(半光强角度：120°) ◆LensColor:WaterClear(透镜颜色：无色透明) ■Applications (应用) ◆GeneralLinghting(普通照明) ◆Advertisement(广告灯) ◆ArchitecturalLighting(建筑照明) ◆StreetLamps(路灯) PartNO.:LY-WH61L0BLIJ05SPECNO.:LY-LEYOND-052404REVNO.:A1 PackageDimensions (外观尺寸) Equivalentcircuitdiagram （等效电路图） Notes: 1.Alldimensionsareinmillimeters. (所有尺寸以毫米为单位) 2.Toleranceis±0.25unlessotherwisenoted (未标注公差为：±0.25) PartNO.:LY-WH61L0BLIJ05 SPECNO.:LY-LEYOND-052404 REVNO.:A1