模具专业术语英文
注塑、模具专业英语
Surface Appearance 外观
Glossiness/gloss finish 光洁度、粗糙度
Matt finish/matt surface 毛面
Glass fiber rich surface/glass emergence on the surface 玻纤外露、浮纤Blooming/surface blooming 表面析出
White patches on surface 表面白斑
Silver marks/silver streak 银纹
Splay mark 水纹、料花
Flow mark 流纹
Brittle/brittleness 脆、脆性
Bubbles/trapped gas 气泡/困气
Void 孔、气泡
Burn marks 烧伤
FR failed 阻燃不合格
Flame rating V-2 阻燃等级V-2
Poor dispersion 分散不好
FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块
Pellet porous 颗粒料孔隙、
Low impact/tensile strength etc 低冲击强度/拉伸强度等
High flow/filler content etc 高流动性/过度填充
Longs/fines/doubles 长粒/碎屑/连粒
Poor cut 粒形不好
Bristle/voids 表面有小气泡/孔
Glass bundles 纤维结团
Product was rejected due to 产品不能接受因为…
High moisture level 高水分、高湿度
Warpage/warped 翘曲/变形
Shrinkage/shrink 收缩/收缩率
Sink marks 凹陷、缩水
Short shot/short molding 打不满、欠注
Distortion 变形
Over dimension 尺寸过大
Under dimension 尺寸过小
Flashing 飞边、披锋、溢边
Discoloration 变色
Off color 颜色差异
Flow rate 流动速率
Viscous/viscosity 粘性的、粘的/黏度
High flow 高流动
Low flow 低流动
Sticky 粘的，粘性的
Sticking core 粘后模，粘模芯
Sticking sprue 粘水口
Sticking cavity 粘前模
Mold release（agent）脱模(剂)
Antioxidant 抗氧剂
Flame retardant agent 阻燃剂
Heat stabilizer 热稳定剂
Chopped glass fiber 短切玻纤
Roving glass fiber 粗纱/长玻纤
Glass beads 玻璃微珠
Milled fiber 碾磨纤
Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂
Pigment 颜料
Dye 染料
Accepted product specification 接受产品规格Approved our product 认可我们的产品
Re-set spec 重新定标准
Add in extra …添加多一点…
Reduced …content 减少…含量
Dropped/reduced …by x％减少…含量…％Confirmed color standard 确认颜色标准
Approved color standard 认可颜色标准
Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品
Undergoing heat aging test 在做热老化实验
Product is under testing 产品在测试当中
Received first order 接了第一个定单
Expected to finish by …预计在…完成
Expected order is xMT 预计定单量…吨
Estimated annual/monthly consumption 预计年/月用量模具方面：
Ejection system 顶出系统、脱模系统
pin 顶针、推杆
spring 弹簧
Gate type 浇口类型
Sprue 主流道
runner 分流道
cavity 模腔
Sprue gate 直浇口
Pin point gate 点浇口
Tab gate 护耳浇口
Fan gate 扇形浇口
Tunnel or submarine gate 潜伏式浇口
Jump gate 跳跃式浇口Diaphragm gate 片状浇口
Ring gate 环形浇口
The cavity of the mould 模腔
Heated cylinder 加热料筒
Surface finish 表面光洁度
Sink mark 缩水
Air trap 困气
Gas trapped 气体困着，困气
void 空隙，孔
galling 烧焦
Weld line 熔接痕，熔合线
Drag mark 划伤、脱模痕
Scratch mark 模具刮花
Deformed/ warp 变形
Ejector not returned 顶针不回位slide 滑块、行位
streak 波纹、条纹、色痕delamination 分层
Jetting mark 喷射痕
Gate mark 浇口痕
rib 筋、加强筋、骨位
boss 凸台、凸起、凸痕
Melt flow length 熔体流线长度Ejector plate 顶针板
Stop pin 限位销
Push rod 推杆、顶针
Push back pin 复位杆
Ejector guide pin 顶针导柱
Cold-slug-well 冷料井、冷料穴
plate 模板
Ejected mark 顶痕，顶白
nozzle 喷嘴
Surface defect 表面缺陷
Air vent 排气口
Filling uneven 走胶不平衡、进胶不平衡pressure:压力
speed:速度
control:控制
protection pressure:保压
mold:模
set:设定
option:选择
injection:射胶
pressure reducing valve :减压阀relief valve:泄压阀
max:最大
max:最大
system:系统proportional:比例pressure transducer:压力传感器sampling试模
pressure sensor压力感应器AMP 伺服放大器
trial run
running
gate
dosage 溶胶
clamp open 开模
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
塑胶模具类中英文对照专业术语
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉，象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
模具常用术语中英文对照
模芯 Parting Core 耐落胶 Teflon Paste 局部视图 Partial View 偏移量 Offset 冷料 Cold Slag 水塞 Water Line Plug 线切割 Wire 撬模脚 Ppy Slot 轮廓 Contour 重新加工 Reworked 螺纹孔Tapping Hole 配件 Components 连接件 Fittings 补偿 Compensation 斜针 Angle Pin 平面度 Parallel 接合 Engage 倒角Chamfer 替换镶件Interchangeable Mold Inserts 模胚 Mold Base 指定吨位的注塑机 Specific Press 热嘴Hotnozzle 水嘴接头 Water Fitting 火花机 Edm 螺纹 Eyebolt Thread 熔接线 Weildline 回针 Stop Pin 压机 Press 二级顶出针 Sub-Leaderd Pin 嗮纹 Texturing 镶件 Mold Insert 梯形 Trapezoid
加硬 Harden 凸缘、法兰 Flange 唧嘴 Sprue 方铁 Spacer Block 设计筒图 Design Preliminary 顶针板 Ejector Plate 名称块表 Title Block 顶针底板 Ejector Retainer Plate 版本标识 Revision Level 垫板 Retainer Plate 材料清单 Stock List 后模镶针 Core Pin 制模 Build Mold 垃圾钉 Stop Pin 手动滑块 Hand Slide 有托顶针 Shoulder Ejector Pin 漏水测试 Leak Test 顶针板导套Guided Ejection Bushing 流道排气 Runner Vents 针板导柱 Guided Ejection Leader Pin 抛光 Draw Polish 唧嘴 Sprue Bushing 侧抽芯 Slide Action 三板模延伸式唧嘴 Extension Noozzle Bulishing 加强筋 Reinforcing 水口板导套 Runner Stripper Pin 三角撑 Gusset 定位圈（法兰）Locating Ring 柱子 Bossed 管钉（定位销）Dowel Pin 出模斜度 Draft 管状管钉 Tubular Dowel
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
模具术语英文翻译知识讲解
模具术语英文翻译
模具术语英文翻译 根据国家标准，以下为部分塑料模具成形术语的标准翻译。 动模 Movable Mould Moving Half 定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate 下模座板 Lower Clamping Plate 凹模固定板 Cavity-retainer Plate 型芯固定板 Mould Core-retainer Plate 凸模固定板 Punch-retainer Plate 模套 Die Body Die Sleeve Die Blank 支承板 Backing Plate Support Plate 垫块 Spacer Parallel 支架 Ejector Housing Mould Base Leg 模头 Die Head 根据国家标准，以下为部分压铸模具术语的标准翻译。 压力铸造模具 Die-Casting Die 压铸模零部件 定模 Fixed Die Cover Die 定模座板 Fixed Clamping Plate 定模套板 Bolster Fixed Die 动模 Moving Die Ejector Die 动模座板 Moving Clamping Plate 直流道 Sprue 横流道 Runner 内浇口 Gate 模具分类 Injection Mold 注塑模 Plastic Rubber Mould 塑胶模 Rubber Molding 橡胶成形 Hot Chamber Die Casting 热室压铸 Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模 Multi-Cavity Mold 多模穴模具 Stack Mold, Stack Injection Mould 叠层模
常用模具零件中英文对照表
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainer plate 托板：support plate
模具DFM常用中英文对照
DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小，导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位，强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角，填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚，会有缩水，建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上，请确认是否接受？ Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角，以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， stick
模具术语翻译
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机（尼龙拉勾）n yl on latch lock 45斜顶lifter 46模胚（架）mold base 47母模cavity in sert 48公模core insert 49行位（滑块）slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
模具常用术语中英文对照表
"R，L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
模具英语专业术语
模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水：gate 进入位(入水点)：gate location 水口形式：gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 直接水口: direct gate 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道：round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析)：mold flow analysis 流道平衡: runner balance
模具英语翻译大全
1. The undercut area where interfere with slide block need to be filled material to help the slide can move smoothly.（和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動） 2. The thickening added too thick.(加肉太多) 3. The thickening area is too wide.（加肉面積太大） 4. Gate position is moved.(GATE位置移位) 5. The split line of slide block or the area of slide.(滑塊拆的位置) 6. This area is hard to be filled due to the sharp feature(此處有尖角，填充困難) 7. The strength of this area is too weak and isn’t easy to get c old due to the steel too thin. 8. ( 此處鋼材太薄，強度不足而且不容易冷卻) 9. .The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark. 10. ( 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷.) 11. The part will be damaged if we make lifter in this area. 12. ( 此處做斜銷在作動時會削到成品肉厚) 13. This is critical surface where is not allow to add material. 14. ( 這個面是裝配面，不能加料) 15. This thick wall area might because sink mark,Please reduce some wall thickness to improve it.) 16. ( 此處料位太厚，會有縮水，建議減料改善) 17. Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area. 18. （此面是不是外觀面，此處做滑塊的話會有結合線，是否可以接受） 19. Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on core and cavity side. No slide block and lifter to be made. 20. （此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷） 21. Please confirm the issues of Parting line, Gate position...Etc otherwise the lead-time will be extended. 22. （請盡快確認這種拆模方式和結構，否則會影響模期） 23. The trim mark of the gate is not visual after open the top case if the gate position is design ed like it 24. （GATE做在此處的話.蓋子打開後看不到GATE的修剪部位） 25. We would suggest to enlarging draft to help tool released.) 26. 加大拔模角，以便脫模順利） 27. There are sharp edges if set the parting line at here, It will reduce the tool life 28. （P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響） 29. If you insist that the gate position have to be as original design then we would
模具专业英文术语大全
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内模：core insert 行位（滑块）：slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin
模具常用英文词汇
钣金设计中常用的其它术语 扩孔enlarge hole 自铆self-chinching 全周压毛边all round burr 平头拉钉set-head rivet 表面处理finish 定位销dowel pin 挂钩hook 平头铆钉closed-end rivet 焊接线weld line 塑料固定栓fastener, plastic, push-type 压合胶粘剂pressure sensitive adhesive 尼龙绑带tie wrap, nylon 五金件hardware 泡棉静电导片gasket, foam, emi 贴纸labeling 铍铜静电导片gasket, beck, emi 烤漆paint 圆头螺钉button-head screw 电镀plating 平头螺母nut flush 铭板nameplate 平齐自铆flush, self-clinching 包装packing 紧固螺丝fix screw 铁材零件sheet metal parts 组装assembly 塑料零件plastic parts 凹陷,顶针sink mark 压边铆钉open-end rivet 插孔jack 弹簧螺丝caps 度thick 文字,记号char actor 半冲孔spring slice 角corner 基座chassis 自锁螺母nut self-clenching 承座bracket 轴肘式铆接toggle lock 承架horsing 卡尺caliper 下盖base 打印字模stamp letter 去毛边deburr 推板导住ejector guide 直导套guide bush, straight[straight bushing] 带头导套guide bush, straight {shoulder bushing} 推板导套ejector guide bush[ejector bushing] 定位圈Locating ring 锥形定位件mould bases locating elements 复位杆ejector plate return pin[push-back pin] 限位钉stop pin[stop but ton] 限位块stop block [stop pad] 定距拉杆puller[length]bolt 定距拉板puller[limit]plate 成形推杆forming ejector pin 圆柱头推杆ejector pin with cylindrical head 带肩推杆shouldered ejector pin 扁推杆flat ejector pin 推管ejector sleeve 推块ejector pad 推件板stripper plate 推杆固定板ejector retainer plate ; 推板ejection plate[elector plate] 连接推杆ejector tie rod 冲裁间隙blanking clearance 模具闭合高度die shut height 压力机闭合高度shut height Of press machine 冲模寿命die life 压力中心center Of load 冲模中心center Of die 冲压方向pressing direction 送料方向feed direction 排样blank layout 搭边scrap 进距feed pitch 切边余量trimming allowance 毛刺burr 冲裁力blanking force 弯曲力bending force 拉仲力drawing force 挤压力extruding force 卸料力stripping force 推件力ejecting force 顶件力kicking force 压料力pressure plate force 压边力black holder force 毛坯blank ;
冲压模具专业词汇中英文翻译
冲压模具词汇Counter bored hole沉孔 Chamfer倒斜角 Fillet倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count复盘人 second check复盘复核人
equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count复盘点数量 Quantity of customs count会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills年终盘点截止单据汇总表 bill name单据名称 Thissheetandphysicalinventorylistwillbesenttoaccountingdepartmenttogether(T hoseofNHKwillbesenttofinancialdepartment) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品
模具专业翻译
1．XXX！你现在有空吗，我可以问你一些问题吗？ Could I ask you some questions if you are free?/ Are you free now? May I ask you some questions (a question)? 2．请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？ Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing? 3．请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？ Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4．这个产品的柱位我们打算做司筒。（或镶针）可以吗？ Can we add ejector sleeves or ejector pins in the boss of this part? 5．产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？ There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 6．产品里面的这个位置我们打算做斜顶或内行位，有问题吗？ We will make the lifter and (inner) slider in this position, will that be a problem? 7．你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？ The 2D and 3D drawing you provided is not the same, can you tell me which one is correct? 8．你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。 There is no draft angle in the 3D drawing, some materials are too thick, and some place are too thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we modify it. 9．按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确？ Accoring to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is right? 10．产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？ This position is too small and will make the steel material here too thin, can we widen it here? 11．斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？The angular lifter interferes with the boss during ejection. Please consider changing the position of the boss. 12．这个筋骨位胶厚太溥，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？ The rib here is too thin and on the high side, so it will be difficult to fill here when we do the injection, can you inrcease the thickness of this rib? 13．你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。但减胶的位置有两种做法，1、做镶件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？ Will you increase/decrease the material on this rib? We will use EDM if you add material, but there are two option if you choose to decrease:1.Make inserts;2.Welding, because there is water in the bottom of the insert, is that OK? 14．这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。This sample has been burned in the bottom because the venting is not good, we can add an insert in the middle of the rib.