中英文文献翻译-机械加工介绍

机械加工介绍

1 Lathes

Lathes are machine tools designed primarily to do turning, facing and boring, Very little turning is done on other types of machine tools, and none can do it with equal facility. Because lathes also can do drilling and reaming, their versatility permits several operations to be done with a single setup of the work piece. Consequently, more lathes of various types are used in manufacturing than any other machine tool.

The essential components of a lathe are the bed, headstock assembly, tailstock assembly, and the leads crew and feed rod.

The bed is the backbone of a lathe. It usually is made of well normalized or aged gray or nodular cast iron and provides s heavy, rigid frame on which all the other basic components are mounted. Two sets of parallel, longitudinal ways, inner and outer, are contained on the bed, usually on the upper side. Some makers use an inverted V-shape for all four ways, whereas others utilize one inverted V and one flat way in one or both sets, They are precision-machined to assure accuracy of alignment. On most modern lathes the way are surface-hardened to resist wear and abrasion, but precaution should be taken in operating a lathe to assure that the ways are not damaged. Any inaccuracy in them usually means that the accuracy of the entire lathe is destroyed.

The headstock is mounted in a foxed position on the inner ways, usually at the left end of the bed. It provides a powered means of rotating the word at various speeds . Essentially, it consists of a hollow spindle, mounted in accurate bearings, and a set of transmission gears-similar to a truck transmission—through which the spindle can be rotated at a number of speeds. Most lathes provide from 8 to 18 speeds, usually in a geometric ratio, and on modern lathes all the speeds can be obtained merely by moving from two to four levers. An increasing trend is to provide a continuously variable speed range through electrical or mechanical drives.

Because the accuracy of a lathe is greatly dependent on the spindle, it is of heavy construction and mounted in heavy bearings, usually preloaded tapered roller or ball types. The spindle has a hole extending through its length, through which long bar stock can be fed. The size of maximum size of bar stock that can be machined when the material must be fed through spindle.

The tailsticd assembly consists, essentially, of three parts. A lower casting fits on the inner ways of the bed and can slide longitudinally thereon, with a means for clamping the entire assembly in any desired location, An upper casting fits on the lower one and can be moved transversely upon it, on some type of keyed ways, to permit aligning the assembly is the tailstock quill. This is a hollow steel cylinder, usually about 51 to 76mm(2to 3 inches) in diameter, that can be moved several inches longitudinally in and out of the upper casting by means of a hand wheel and screw.

The size of a lathe is designated by two dimensions. The first is known as the swing. This is the

maximum diameter of work that can be rotated on a lathe. It is approximately twice the distance between the line connecting the lathe centers and the nearest point on the ways, The second size dimension is the maximum distance between centers. The swing thus indicates the maximum work piece diameter that can be turned in the lathe, while the distance between centers indicates the maximum length of work piece that can be mounted between centers.

Engine lathes are the type most frequently used in manufacturing. They are heavy-duty machine tools with all the components described previously and have power drive for all tool movements except on the compound rest. They commonly range in size from 305 to 610 mm(12 to 24 inches)swing and from 610 to 1219 mm(24 to 48 inches) center distances, but swings up to 1270 mm(50 inches) and center distances up to 3658mm(12 feet) are not uncommon. Most have chip pans and a built-in coolant circulating system. Smaller engine lathes-with swings usually not over 330 mm (13 inches ) –also are available in bench type, designed for the bed to be mounted on a bench on a bench or cabinet.

Although engine lathes are versatile and very useful, because of the time required for changing and setting tools and for making measurements on the work piece, thy are not suitable for quantity production. Often the actual chip-production tine is less than 30% of the total cycle time. In addition, a skilled machinist is required for all the operations, and such persons are costly and often in short supply. However, much of the operator’s time is consumed by simple, repetitious adjustments and in watching chips being made. Consequently, to reduce or eliminate the amount of skilled labor that is required, turret lathes, screw machines, and other types of semiautomatic and automatic lathes have been highly developed and are widely used in manufacturing.

2 Numerical Control

One of the most fundamental concepts in the area of advanced manufacturing technologies is numerical control (NC). Prior to the advent of NC, all machine tools ere manually operated and controlled. Among the many limitations associated with manual control machine tools, perhaps none is more prominent than the limitation of operator skills. With manual control, the quality of the product is directly related to and limited to the skills of the operator. Numerical control represents the first major step away from human control of machine tools.

Numerical control means the control of machine tools and other manufacturing systems through the use of prerecorded, written symbolic instructions. Rather than operating a machine tool, an NC technician writes a program that issues operational instructions to the machine tool. For a machine tool to be numerically controlled, it must be interfaced with a device for accepting and decoding the programmed instructions, known as a reader.

Numerical control was developed to overcome the limitation of human operators, and it has done so. Numerical control machines are more accurate than manually operated machines, they can produce parts more uniformly, they are faster, and the long-run tooling costs are lower. The

development of NC led to the development of several other innovations in manufacturing technology:

Electrical discharge machining,Laser cutting,Electron beam welding.

Numerical control has also made machine tools more versatile than their manually operated predecessors. An NC machine tool can automatically produce a wide of parts, each involving an assortment of widely varied and complex machining processes. Numerical control has allowed manufacturers to undertake the production of products that would not have been feasible from an economic perspective using manually controlled machine tolls and processes.

Like so many advanced technologies, NC was born in the laboratories of the Massachusetts Institute of Technology. The concept of NC was developed in the early 1950s with funding provided by the U.S. Air Force. In its earliest stages, NC machines were able to made straight cuts efficiently and effectively.

However, curved paths were a problem because the machine tool had to be programmed to undertake a series of horizontal and vertical steps to produce a curve. The shorter the straight lines making up the steps, the smoother is the curve, Each line segment in the steps had to be calculated.

This problem led to the development in 1959 of the Automatically Programmed Tools (APT) language. This is a special programming language for NC that uses statements similar to English language to define the part geometry, describe the cutting tool configuration, and specify the necessary motions. The development of the APT language was a major step forward in the fur ther development from those used today. The machines had hardwired logic circuits. The instructional programs were written on punched paper, which was later to be replaced by magnetic plastic tape.

A tape reader was used to interpret the instructions written on the tape for the machine. Together, all of this represented a giant step forward in the control of machine tools. However, there were a number of problems with NC at this point in its development.

A major problem was the fragility of the punched paper tape medium. It was common for the paper tape containing the programmed instructions to break or tear during a machining process. This problem was exacerbated by the fact that each successive time a part was produced on a machine tool, the paper tape carrying the programmed instructions had to be rerun through the reader. If it was necessary to produce 100 copies of a given part, it was also necessary to run the paper tape through the reader 100 separate tines. Fragile paper tapes simply could not withstand the rigors of a shop floor environment and this kind of repeated use.

This led to the development of a special magnetic plastic tape. Whereas the paper carried the programmed instructions as a series of holes punched in the tape, the plastic tape carried the instructions as a series of magnetic dots. The plastic tape was much stronger than the paper tape, which solved the problem of frequent tearing and breakage. However, it still left two other problems.

The most important of these was that it was difficult or impossible to change the instructions entered on the tape. To made even the most minor adjustments in a program of instructions, it was necessary to interrupt machining operations and make a new tape. It was also still necessary to run the tape through the reader as many times as there were parts to be produced. Fortunately, computer technology became a reality and soon solved the problems of NC associated with punched paper and plastic tape.

The development of a concept known as direct numerical control (DNC) solved the paper and plastic tape problems associated with numerical control by simply eliminating tape as the medium for carrying the programmed instructions. In direct numerical control, machine tools are tied, via a data transmission link, to a host computer. Programs for operating the machine tools are stored in the host computer and fed to the machine tool an needed via the data transmission linkage. Direct numerical control represented a major step forward over punched tape and plastic tape. However, it is subject to the same limitations as all technologies that depend on a host computer. When the host computer goes down, the machine tools also experience downtime. This problem led to the development of computer numerical control.

3 Turning

The engine lathe, one of the oldest metal removal machines, has a number of useful and highly desirable attributes. Today these lathes are used primarily in small shops where smaller quantities rather than large production runs are encountered.

The engine lathe has been replaced in today’s production shops by a wide variety of automatic lathes such as automatic of single-point tooling for maximum metal removal, and the use of form tools for finish on a par with the fastest processing equipment on the scene today.

Tolerances for the engine lathe depend primarily on the skill of the operator. The design engineer must be careful in using tolerances of an experimental part that has been produced on the engine lathe by a skilled operator. In redesigning an experimental part for production, economical tolerances should be used.

Turret Lathes Production machining equipment must be evaluated now, more than ever before, this criterion for establishing the production qualification of a specific method, the turret lathe merits a high rating.

In designing for low quantities such as 100 or 200 parts, it is most economical to use the turret lathe. In achieving the optimum tolerances possible on the turrets lathe, the designer should strive for a minimum of operations.

Automatic Screw Machines Generally, automatic screw machines fall into several categories; single-spindle automatics, multiple-spindle automatics and automatic chucking machines. Originally designed for rapid, automatic production of screws and similar threaded parts, the automatic screw machine has long since exceeded the confines of this narrow field, and today plays a vital role in the mass production of a variety of precision parts. Quantities play an

important part in the economy of the parts machined on the automatic screw machine. Quantities less than on the automatic screw machine. The cost of the parts machined can be reduced if the minimum economical lot size is calculated and the proper machine is selected for these quantities.

Automatic Tracer Lathes Since surface roughness depends greatly on material turned, tooling , and feeds and speeds employed, minimum tolerances that can be held on automatic tracer lathes are not necessarily the most economical tolerances.

In some cases, tolerances of 0.05mm are held in continuous production using but one cut . groove width can be held to 0.125mm on some parts. Bores and single-point finishes can be held to 0.0125mm. On high-production runs where maximum output is desirable, a minimum tolerance of 0.125mm is economical on both diameter and length of turn.

中文译文

1.车床

车床主要是为了进行车外圆、车端面和镗孔等项工作而设计的机床。车削很少在其他种类的机床上进行，而且任何一种其他机床都不能像车床那样方便地进行车削加工。由于车床还可以用来钻孔和铰孔，车床的多功能性可以使工件在一次安装中完成几种加工。因此，在生产中使用的各种车床比任何其他种类的机床都多。

车床的基本部件有：床身、主轴箱组件、尾座组件、溜板组件、丝杠和光杠。

床身是车床的基础件。它能常是由经过充分正火或时效处理的灰铸铁或者球墨铁制成。它是一个坚固的刚性框架，所有其他基本部件都安装在床身上。通常在床身上有内外两组平行的导轨。有些制造厂对全部四条导轨都采用导轨尖朝上的三角形导轨（即山形导轨），而有的制造厂则在一组中或者两组中都采用一个三角形导轨和一个矩形导轨。导轨要经过精密加工以保证其直线度精度。为了抵抗磨损和擦伤，大多数现代机床的导轨是经过表面淬硬的，但是在操作时还应该小心，以避免损伤导轨。导轨上的任何误差，常常意味着整个机床的精度遭到破坏。

主轴箱安装在内侧导轨的固定位置上，一般在床身的左端。它提供动力，并可使工件在各种速度下回转。它基本上由一个安装在精密轴承中的空心主轴和一系列变速齿轮(类似于卡车变速箱)所组成。通过变速齿轮，主轴可以在许多种转速下旋转。大多数车床有8~12种转速，一般按等比级数排列。而且在现代机床上只需扳动2~4个手柄，就能得到全部转速。一种正在不断增长的趋势是通过电气的或者机械的装置进行无级变速。

由于机床的精度在很大程度上取决于主轴，因此，主轴的结构尺寸较大，通常安装在预紧后的重型圆锥滚子轴承或球轴承中。主轴中有一个贯穿全长的通孔，长棒料可以通过该孔送料。主轴孔的大小是车床的一个重要尺寸，因此当工件必须通过主轴孔供料时，它确定了能够加工的棒料毛坯的最大尺寸。

尾座组件主要由三部分组成。底板与床身的内侧导轨配合，并可以在导轨上作纵向移动。底板上有一个可以使整个尾座组件夹紧在任意位置上的装置。尾座体安装在底板上，可以沿某种类型的键槽在底板上横向移动，使尾座能与主轴箱中的主轴对正。尾座的第三个组成部分

是尾座套筒。它是一个直径通常大约在51~76mm（2~3英寸）之间的钢制空心圆柱体。通过手轮和螺杆，尾座套筒可以在尾座体中纵向移入和移出几个英寸。

车床的规格用两个尺寸表示。第一个称为车床的床面上最大加工直径。这是在车床上能够旋转的工件的最大直径。它大约是两顶尖连线与导轨上最近点之间距离的两倍。第二个规格尺寸是两顶尖之间的最大距离。车床床面上最大加工直径表示在车床上能够车削的最大工件直径，而两顶尖之间的最大距离则表示在两个顶尖之间能够安装的工件的最大长度。

普通车床是生产中最经常使用的车床种类。它们是具有前面所叙的所有那些部件的重载机床，并且除了小刀架之外，全部刀具的运动都有机动进给。它们的规格通常是：车床床面上最大加工直径为305~610mm（12~24英寸）；但是，床面上最大加工直径达到1270mm（50英寸）和两顶尖之间距离达到3658mm的车床也并不少见。这些车床大部分都有切屑盘和一个安装在内部的冷却液循环系统。小型的普通车床—车床床面最大加工直径一般不超过330mm（13英寸）--被设计成台式车床，其床身安装在工作台或柜子上。

虽然普通车床有很多用途，是很有用的机床，但是更换和调整刀具以及测量工件花费很多时间，所以它们不适合在大量生产中应用。通常，它们的实际加工时间少于其总加工时间的30%。此外，需要技术熟练的工人来操作普通车床，这种工人的工资高而且很难雇到。然而，操作工人的大部分时间却花费在简单的重复调整和观察切屑过程上。因此，为了减少或者完全不雇用这类熟练工人，六角车床、螺纹加工车床和其他类型的半自动和自动车床已经很好地研制出来，并已经在生产中得到广泛应用。

2.数字控制

先进制造技术中的一个基本的概念是数字控制（NC）。在数控技术出现之前，所有的机床都是由人工操纵和控制的。在与人工控制的机床有关的很多局限性中，操作者的技能大概是最突出的问题。采用人工控制是，产品的质量直接与操作者的技能有关。数字控制代表了从人工控制机床走出来的第一步。

数字控制意味着采用预先录制的、存储的符号指令来控制机床和其他制造系统。一个数控技师的工作不是去操纵机床，而是编写能够发出机床操纵指令的程序。对于一台数控机床，其上必须安有一个被称为阅读机的界面装置，用来接受和解译出编程指令。

发展数控技术是为了克服人类操作者的局限性，而且它确实完成了这项工作。数字控制的机器比人工操纵的机器精度更高、生产出零件的一致性更好、生产速度更快、而且长期的工艺装备成本更低。数控技术的发展导致了制造工艺中其他几项新发明的产生：电火花加工技术、激光切割、电子束焊接

数字控制还使得机床比它们采用有人工操的前辈们的用途更为广泛。

一台数控机床可以自动生产很多类的零件，每一个零件都可以有不同的和复杂的加工过程。数控可以使生产厂家承担那些对于采用人工控制的机床和工艺来说，在经济上是不划算的产品生产任务。

同许多先进技术一样，数控诞生于麻省理工学院的实验室中。数控这个概念是50年代初在美国空军的资助下提出来的。在其最初的价段，数控机床可以经济和有效地进行直线切割。

然而，曲线轨迹成为机床加工的一个问题，在编程时应该采用一系列的水平与竖直的台阶来生成曲线。构成台阶的每一个线段越短，曲线就越光滑。台阶中的每一个线段都必须经过计算。

在这个问题促使下，于1959年诞生了自动编程工具（APT）语言。这是一个专门适用于数控的编程语言，使用类似于英语的语句来定义零件的几何形状，描述切削刀具的形状和规定必要的运动。APT语言的研究和发展是在数控技术进一步发展过程中的一大进步。最初的数控系统下今天应用的数控系统是有很大差别的。在那时的机床中，只有硬线逻辑电路。指令程序写在穿孔纸带上（它后来被塑料带所取代），采用带阅读机将写在纸带或磁带上的指令给机器翻译出来。所有这些共同构成了机床数字控制方面的巨大进步。然而，在数控发展的这个阶段中还存在着许多问题。

一个主要问题是穿孔纸带的易损坏性。在机械加工过程中，载有编程指令信息的纸带断裂和被撕坏是常见的事情。在机床上每加工一个零件，都需要将载有编程指令的纸带放入阅读机中重新运行一次。因此，这个问题变得很严重。如果需要制造100个某种零件，则应该将纸带分别通过阅读机100次。易损坏的纸带显然不能承受严配的车间环境和这种重复使用。

这就导致了一种专门的塑料磁带的研制。在纸带上通过采用一系列的小孔来载有编程指令，而在塑料带上通过采用一系列的磁点眯载有编程指令。塑料带的强度比纸带的强度要高很多，这就可以解决常见的撕坏和断裂问题。然而，它仍然存在着两个问题。

其中最重要的一个问题是，对输入到带中指令进行修改是非常困难的，或者是根本不可能的。即使对指令程序进行最微小的调整，也必须中断加工，制作一条新带。而且带通过阅读机的次数还必须与需要加工的零件的个数相同。幸运的是，计算机技术的实际应用很快解决了数控技术中与穿孔纸带和塑料带有关的问题。

在形成了直接数字控制（DNC）这个概念之后，可以不再采用纸带或塑料带作为编程指令的载体，这样就解决了与之有关的问题。在直接数字控制中，几台机床通过数据传输线路联接到一台主计算机上。操纵这些机床所需要的程序都存储在这台主计算机中。当需要时，通过数据传输线路提供给每台机床。直接数字控制是在穿孔纸带和塑料带基础上的一大进步。然而，它敢有着同其他信赖于主计算机技术一样的局限性。当主计算机出现故障时，由其控制的所有机床都将停止工作。这个问题促使了计算机数字控制技术的产生。

微处理器的发展为可编程逻辑控制器和微型计算机的发展做好了准备。这两种技术为计算机数控（CNC）的发打下了基础。采用CNC技术后，每台机床上都有一个可编程逻辑控制器或者微机对其进行数字控制。这可以使得程序被输入和存储在每台机床内部。它还可以在机床以外编制程序，并将其下载到每台机床中。计算机数控解决了主计算机发生故障所带来的问题，但是它产生了另一个被称为数据管理的问题。同一个程序可能要分别装入十个相互之间没有通讯联系的微机中。这个问题目前正在解决之中，它是通过采用局部区域网络将各个微机联接起来，以得于更好地进行数据管理。

3.车削加工

普通车床作为最早的金属切削机床的一种，目前仍然有许多有用的和为人要的特性和为人们所需的特性。现在，这些机床主要用在规模较小的工厂中，进行小批量的生产，而不是进行大批量的和产。

在现代的生产车间中，普通车床已经被种类繁多的自动车床所取代，诸如自动仿形车床，六角车床和自动螺丝车床。现在，设计人员已经熟知先利用单刃刀具去除大量的金属余量，然后利用成型刀具获得表面光洁度和精度这种加工方法的优点。这种加工方法的生产速度与现在工厂中使用的最快的加工设备的速度相等。

普通车床的加偏差主要信赖于操作者的技术熟练程度。设计工程师应该认真地确定由熟练工人在普通车床上加工的试验件的公差。在把试验伯重新设计为生产零件时，应该选用经济的公差。

六角车床对生产加工设备来说，目前比过去更注重评价其是否具有精确的和快速的重复加工能力。应用这个标准来评价具体的加工方法，六角车床可以获得较高的质量评定。在为小批量的零件（100~200件）设计加工方法时，采用六角车床是最经济的。为了在六角车床上获得尽可能小的公差值，设计人员应该尽量将加工工序的数目减至最少。

自动螺丝车床自动螺丝车床通被分为以下几种类型：单轴自动、多轴自动和自动夹紧车床。自动螺丝车床最初是被用来对螺钉和类似的带有螺纹的零件进行自动化和快速加工的。但是，这种车床的用途早就超过了这个狭窄的范围。现在，它在许多种类的精密零件的大批量生产中起着重要的作用。工件的数量对采用自动螺丝车床所加工的零件的经济性有较大的影响。如果工件的数量少于1000件，在六角车床上进行加工比在自动螺丝车床上加工要经济得多。如果计算出最小经济批量，并且针对工件批量正确地选择机床，就会降低零件的加工成本。

自动仿形车床因为零件的表面粗糙度在很大程度上取决于工件材料、刀具、进给量和切削速度，采用自动仿形车床加工所得到的最小公差一定是最经济的公差。

在某些情况下，在连续生产过程中，只进行一次切削加工时的公差可以达到0.05mm。对于某些零件，槽宽的公差可以达到0.125mm。镗孔和休用单刃刀具进行精加工时，公差可达到0.0125mm。在希望获得最大主量的大批量生产中，进行直径和长度的车削时的最小公差值为0.125mm是经济的。

【经济类文献翻译】电子商务

电子商务 电子商务（Electronic Commerce）是在Internet开放的网络环境下，基于浏览器/服务器应用方式，实现消费者的网上购物、商户之间的网上交易和在线电子支付的一种新型的商业运营模式 Internet上的电子商务可以分为三个方面：信息服务、交易和支付。主要内容包括：电子商情广告；电子选购和交易、电子交易凭证的交换；电子支付与结算以及售后的网上服务等。主要交易类型有企业与个人的交易(BtoC方式)和企业之间的交易(BtoB方式)两种。参与电子商务的实体有四类：顾客(个人消费者或企业集团)、商户(包括销售商、制造商、储运商)、银行(包括发卡行、收单行)及认证中心。 电子商务是Internet爆炸式发展的直接产物，是网络技术应用的全新发展方向。Internet本身所具有的开放性、全球性、低成本、高效率的特点，也成为电子商务的内在特征，并使得电子商务大大超越了作为一种新的贸易形式所具有的价值，它不仅会改变企业本身的生产、经营、管理活动，而且将影响到整个社会的经济运行与结构。 1．电子商务将传统的商务流程电子化、数字化，一方面以电子流代替了实物流，可以大量减少人力、物力，降低了成本；另一方面突破了时间和空间的限制，使得交易活动可以在任何时间、任何地点进行，从而大大提高了效率。 2．电子商务所具有的开放性和全球性的特点，为企业创造了更多的贸易机会。 3．电子商务使企业可以以相近的成本进入全球电子化市场，使得中小企业有可能拥有和大企业一样的信息资源，提高了中小企业的竞争能力。 4．电子商务重新定义了传统的流通模式，减少了中间环节，使得生产者和消费者的直接交易成为可能，从而在一定程度上改变了整个社会经济运行的方式。 5．电子商务一方面破除了时空的壁垒，另一方面又提供了丰富的信息资源，

中英文文献翻译

毕业设计（论文）外文参考文献及译文 英文题目Component-based Safety Computer of Railway Signal Interlocking System 中文题目模块化安全铁路信号计算机联锁系统 学院自动化与电气工程学院 专业自动控制 姓名葛彦宁 学号 200808746 指导教师贺清 2012年5月30日

Component-based Safety Computer of Railway Signal Interlocking System 1 Introduction Signal Interlocking System is the critical equipment which can guarantee traffic safety and enhance operational efficiency in railway transportation. For a long time, the core control computer adopts in interlocking system is the special customized high-grade safety computer, for example, the SIMIS of Siemens, the EI32 of Nippon Signal, and so on. Along with the rapid development of electronic technology, the customized safety computer is facing severe challenges, for instance, the high development costs, poor usability, weak expansibility and slow technology update. To overcome the flaws of the high-grade special customized computer, the U.S. Department of Defense has put forward the concept：we should adopt commercial standards to replace military norms and standards for meeting consumers’demand [1]. In the meantime, there are several explorations and practices about adopting open system architecture in avionics. The United Stated and Europe have do much research about utilizing cost-effective fault-tolerant computer to replace the dedicated computer in aerospace and other safety-critical fields. In recent years, it is gradually becoming a new trend that the utilization of standardized components in aerospace, industry, transportation and other safety-critical fields. 2 Railways signal interlocking system 2.1 Functions of signal interlocking system The basic function of signal interlocking system is to protect train safety by controlling signal equipments, such as switch points, signals and track units in a station, and it handles routes via a certain interlocking regulation. Since the birth of the railway transportation, signal interlocking system has gone through manual signal, mechanical signal, relay-based interlocking, and the modern computer-based Interlocking System. 2.2 Architecture of signal interlocking system Generally, the Interlocking System has a hierarchical structure. According to the function of equipments, the system can be divided to the function of equipments; the system

文献翻译英文原文

https://www.sodocs.net/doc/5513407490.html,/finance/company/consumer.html Consumer finance company The consumer finance division of the SG group of France has become highly active within India. They plan to offer finance for vehicles and two-wheelers to consumers, aiming to provide close to Rs. 400 billion in India in the next few years of its operations. The SG group is also dealing in stock broking, asset management, investment banking, private banking, information technology and business processing. SG group has ventured into the rapidly growing consumer credit market in India, and have plans to construct a headquarters at Kolkata. The AIG Group has been approved by the RBI to set up a non-banking finance company (NBFC). AIG seeks to introduce its consumer finance and asset management businesses in India. AIG Capital India plans to emphasize credit cards, mortgage financing, consumer durable financing and personal loans. Leading Indian and international concerns like the HSBC, Deutsche Bank, Goldman Sachs, Barclays and HDFC Bank are also waiting to be approved by the Reserve Bank of India to initiate similar operations. AIG is presently involved in insurance and financial services in more than one hundred countries. The affiliates of the AIG Group also provide retirement and asset management services all over the world. Many international companies have been looking at NBFC business because of the growing consumer finance market. Unlike foreign banks, there are no strictures on branch openings for the NBFCs. GE Consumer Finance is a section of General Electric. It is responsible for looking after the retail finance operations. GE Consumer Finance also governs the GE Capital Asia. Outside the United States, GE Consumer Finance performs its operations under the GE Money brand. GE Consumer Finance currently offers financial services in more than fifty countries. The company deals in credit cards, personal finance, mortgages and automobile solutions. It has a client base of more than 118 million customers throughout the world

人工智能专业外文翻译-机器人

译文资料： 机器人 首先我介绍一下机器人产生的背景，机器人技术的发展，它应该说是一个科学技术发展共同的一个综合性的结果，同时，为社会经济发展产生了一个重大影响的一门科学技术，它的发展归功于在第二次世界大战中各国加强了经济的投入，就加强了本国的经济的发展。另一方面它也是生产力发展的需求的必然结果，也是人类自身发展的必然结果，那么随着人类的发展，人们在不断探讨自然过程中，在认识和改造自然过程中，需要能够解放人的一种奴隶。那么这种奴隶就是代替人们去能够从事复杂和繁重的体力劳动，实现人们对不可达世界的认识和改造，这也是人们在科技发展过程中的一个客观需要。 机器人有三个发展阶段，那么也就是说，我们习惯于把机器人分成三类，一种是第一代机器人，那么也叫示教再现型机器人，它是通过一个计算机，来控制一个多自由度的一个机械，通过示教存储程序和信息，工作时把信息读取出来，然后发出指令，这样的话机器人可以重复的根据人当时示教的结果，再现出这种动作，比方说汽车的点焊机器人，它只要把这个点焊的过程示教完以后，它总是重复这样一种工作，它对于外界的环境没有感知，这个力操作力的大小，这个工件存在不存在，焊的好与坏，它并不知道，那么实际上这种从第一代机器人，也就存在它这种缺陷，因此，在20世纪70年代后期，人们开始研究第二代机器人，叫带感觉的机器人，这种带感觉的机器人是类似人在某种功能的感觉，比如说力觉、触觉、滑觉、视觉、听觉和人进行相类比，有了各种各样的感觉，比方说在机器人抓一个物体的时候，它实际上力的大小能感觉出来，它能够通过视觉，能够去感受和识别它的形状、大小、颜色。抓一个鸡蛋，它能通过一个触觉，知道它的力的大小和滑动的情况。第三代机器人，也是我们机器人学中一个理想的所追求的最高级的阶段，叫智能机器人，那么只要告诉它做什么，不用告诉它怎么去做，它就能完成运动，感知思维和人机通讯的这种功能和机能，那么这个目前的发展还是相对的只是在局部有这种智能的概念和含义，但真正完整意义的这种智能机器人实际上并没有存在，而只是随着我们不断的科学技术的发展，智能的概念越来越丰富，它内涵越来越宽。 下面我简单介绍一下我国机器人发展的基本概况。由于我们国家存在很多其

中英文对照资料外文翻译文献

中英文对照资料外文翻译文献 平设计任何时期平面设计可以参照一些艺术和专业学科侧重于视觉传达和介绍。采用多种方式相结合，创造和符号，图像和语句创建一个代表性的想法和信息。平面设计师可以使用印刷，视觉艺术和排版技术产生的最终结果。平面设计常常提到的进程，其中沟通是创造和产品设计。共同使用的平面设计包括杂志，广告，产品包装和网页设计。例如，可能包括产品包装的标志或其他艺术作品，举办文字和纯粹的设计元素，如形状和颜色统一件。组成的一个最重要的特点，尤其是平面设计在使用前现有材料或不同的元素。平面设计涵盖了人类历史上诸多领域，在此漫长的历史和在相对最近爆炸视觉传达中的第20和21世纪，人们有时是模糊的区别和重叠的广告艺术，平面设计和美术。毕竟，他们有着许多相同的内容，理论，原则，做法和语言，有时同样的客人或客户。广告艺术的最终目标是出售的商品和服务。在平面设计，“其实质是使以信息，形成以思想，言论和感觉的经验”。

在唐朝（618-906 ）之间的第4和第7世纪的木块被切断打印纺织品和后重现佛典。阿藏印在868是已知最早的印刷书籍。在19世纪后期欧洲，尤其是在英国，平面设计开始以独立的运动从美术中分离出来。蒙德里安称为父亲的图形设计。他是一个很好的艺术家，但是他在现代广告中利用现代电网系统在广告、印刷和网络布局网格。于1849年，在大不列颠亨利科尔成为的主要力量之一在设计教育界，该国政府通告设计在杂志设计和制造的重要性。他组织了大型的展览作为庆祝现代工业技术和维多利亚式的设计。从1892年至1896年威廉?莫里斯凯尔姆斯科特出版社出版的书籍的一些最重要的平面设计产品和工艺美术运动，并提出了一个非常赚钱的商机就是出版伟大文本论的图书并以高价出售给富人。莫里斯证明了市场的存在使平面设计在他们自己拥有的权利，并帮助开拓者从生产和美术分离设计。这历史相对论是，然而，重要的，因为它为第一次重大的反应对于十九世纪的陈旧的平面设计。莫里斯的工作，以及与其他私营新闻运动，直接影响新艺术风格和间接负责20世纪初非专业性平面设计的事态发展。谁创造了最初的“平面设计”似乎存在争议。这被归因于英国的设计师和大学教授Richard Guyatt，但另一消息来源于20世纪初美国图书设计师William Addison Dwiggins。伦敦地铁的标志设计是爱德华约翰斯顿于1916年设计的一个经典的现代而且使用了系统字体设计。在20世纪20年代，苏联的建构主义应用于“智能生产”在不同领域的生产。个性化的运动艺术在2俄罗斯大革命是没有价值的，从而走向以创造物体的功利为目的。他们设计的建筑、剧院集、海报、面料、服装、家具、徽标、菜单等。J an Tschichold 在他的1928年书中编纂了新的现代印刷原则，他后来否认他在这本书的法西斯主义哲学主张，但它仍然是非常有影响力。Tschichold ，包豪斯印刷专家如赫伯特拜耳和拉斯洛莫霍伊一纳吉，和El Lissitzky 是平面设计之父都被我们今天所知。他们首创的生产技术和文体设备，主要用于整个二十世纪。随后的几年看到平面设计在现代风格获得广泛的接受和应用。第二次世界大战结束后，美国经济的建立更需要平面设计，主要是广告和包装等。移居国外的德国包豪斯设计学院于1937年到芝加哥带来了“大规模生产”极简到美国;引发野火的“现代”

电子商务企业文化中英文对照外文翻译文献

中英文对照外文翻译文 电子商务时代企业文化的再造 随着网络时代电子商务大规模发展，电子商务企业文化随之产生，它在一个企业在产生的一种新的价值观，使企业内部资源得到从新整合，在为企业带来降低交易成本，提高效率，缩短生产周期等诸多好处的同时，也对已有的企业文化发起了挑战。电子商务的兴起是一场由技术手段飞速发展而引发的商业运作模式的变革，传统经济活动的生存基础、运作方式和管理机制均发生了彻底改变，传统的企业文化也面临着巨大的冲击。 一、企业文化对企业价值的贡献 文化现象是一个国家和民族文明的主要见证。广义的文化，包括知识、信仰、艺术、道德、法律、习俗和任何人作为一名社会成员而获得的能力和习惯在内的复杂整体。作为“亚文化”的企业文化，对企业的生存与发展亦起着举足轻重的作用。企业文化是商品经济和市场经济的产物，符合市场经济的客观规律，体现企业的竞争实务、竞争精神和整体形象。所谓企业文化就是企业的经营管理哲学，企业面对所处的社会和商业环境，在长期的生产经营活动中，形成全体员工所接受和认同信守的、为争取事业成功的一套非正式规则。它表明企业奉行何种管理哲学，以及企业通过管理要达到一个什么样的目标。是经济管理的重要内容之一。企业文化意味着一个公司的价值观，而这些价值观成为公司员工活动和行为的规范。 企业文化的本源问题是如何增加企业利润，降低企业的成本和费用。它的要义就是怎么使企业能够有效的整合资源，以达到对外部的适应性，使公司在竞争中生存，进而实现持续发展。企业文化建设为企业开展文化管理指出一个明确的方向。企业文化建设的根本目的是建设能够对外竞争环境具有高度适应性，并能根据环境变换做出迅速反应的行为方式能力，这种能力其实就是企业所拥有的根据外部竞争的环境需要而对内部资源进行整合运用的能力。企业文化建设应促进这一能力系统的形成，并维持好这一能力系统。中国的许多企业例如海尔、联想等企业成功的秘诀之一就是发展了一整套公司理念、经营哲学，形成了自己独特的企业文化。 1、企业文化体现企业的形象和精神。树立良好的企业形象，需要企业文化的支撑。现

统计学中英文对照外文翻译文献

中英文对照翻译 (文档含英文原文和中文翻译) Policies for Development of Iron and Steel Industry The iron and steel industry is an important basic industry of the national economy, a supporting industry for realizing the industrialization and an intensive industry in technologies, capital, resources and energy, and its development requires a comprehensive balancing of all kinds of external conditions. China is a big developing country with a comparatively big demand of iron and steel in the economic development for a long time to go. China's production capacity of iron and steel has ranked the first place in the world for many years. However, there is a large gap in terms of the technological level and material consumption of the iron and steel industry compared with the international advanced level, so the focus of development for the future shall be put on technical upgrading and structural adjustment. In order to enhance the whole technical level of the iron and steel industry, promote the structural adjustment, improve the industrial layout, develop a recycling economy, lower the consumption of materials and energy, pay attention to the environmental protection, raise the comprehensive competitive capacity of enterprises, realize the industrial upgrading, and develop the iron and steel industry into an industry with

文献综述_人工智能

人工智能的形成及其发展现状分析 冯海东 （长江大学管理学院荆州434023） 摘要：人工智能的历史并不久远，故将从人工智能的出现、形成、发展现 状及前景几个方面对其进行分析，总结其发展过程中所出现的问题，以及发展现状中的不足之处，分析其今后的发展方向。 关键词：人工智能，发展过程，现状分析，前景。 一．引言 人工智能最早是在1936年被英国的科学家图灵提出，并不为多数人所认知。 当时，他编写了一个下象棋的程序，这就是最早期的人工智能的应用。也有著名的“图灵测试”，这也是最初判断是否是人工智能的方案,因此，图灵被尊称为“人工智能之父”。人工智能从产生到发展经历了一个起伏跌宕的过程，直到目前为止，人工智能的应用技术也不是很成熟，而且存在相当的缺陷。 通过搜集的资料，将详细的介绍人工智能这个领域的具体情况，剖析其面临的挑战和未来的前景。 二．人工智能的发展历程 1. 1956年前的孕育期 (1) 从公元前伟大的哲学家亚里斯多德(Aristotle)到16世纪英国哲学家培根(F. Bacon)，他们提出的形式逻辑的三段论、归纳法以及“知识就是力量”的警句，都对人类思维过程的研究产生了重要影响。 （2）17世纪德国数学家莱布尼兹(G..Leibniz)提出了万能符号和推理计算思想，为数理逻辑的产生和发展奠定了基础，播下了现代机器思维设计思想的种子。而19世纪的英国逻辑学家布尔（G. Boole）创立的布尔代数，实现了用符号语言描述人类思维活动的基本推理法则。 （3） 20世纪30年代迅速发展的数学逻辑和关于计算的新思想，使人们在计算机出现之前，就建立了计算与智能关系的概念。被誉为人工智能之父的英国天才的数学家图灵（A. Tur-ing）在1936年提出了一种理想计算机的数学模型，即图灵机之后,1946年就由美国数学家莫克利（J. Mauchly）和埃柯特（J. Echert）研制出了世界上第一台数字计算机，它为人工智能的研究奠定了不可缺少的物质基础。1950年图灵又发表了“计算机与智能”的论文，提出了著名的“图灵测试”，形象地指出什么是人工智能以及机器具有智能的标准，对人工智能的发展产生了极其深远的影响。 （4） 1934年美国神经生理学家麦克洛奇(W. McCulloch) 和匹兹(W. Pitts )建立了第一个神经网络模型，为以后的人工神经网络研究奠定了基础。 2. 1956年至1969年的诞生发育期 (1)1956年夏季，麻省理工学院（MIT)的麦卡锡（J．McCarthy）、明斯基（M. Minshy）、塞尔夫里奇（O. Selfridge)与索罗门夫(R. Solomonff)、 IBM的洛

材料英文文献翻译

The development of plastic mould China's industrial plastic moulds from the start to now, after more than half a century, there has been great development, mold levels have been greatly enhanced. Mould has been at large can produce 48-inch big-screen color TV Molded Case injection mold, 6.5 kg capacity washing machine full of plastic molds, as well as the overall car bumpers and dashboards, and other plastic mould precision plastic molds, the camera is capable of producing plastic mould , multi-cavity mold small modulus gear and molding mold. --Such as Tianjin and Yantai days Electrical Co., Ltd Polaris IK Co. manufactured multi-cavity mold VCD and DVD gear, the gear production of such size precision plastic parts, coaxial, beating requirements have reached a similar foreign the level of product, but also the application of the latest gear design software to correct contraction as a result of the molding profile error to the standard involute requirements. Production can only 0.08 mm thickness of a two-cavity mold and the air Cup difficulty of plastic doors and windows out of high modulus, and so on. Model cavity injection molding manufacturing accuracy of 0.02 to 0.05 mm, surface roughness Ra0.2 μ m, mold quality, and significantly increase life expectancy, non-hardening steel mould life up to 10~ 30 million, hardening steel form up to 50 ~ 10 million times, shorten the delivery time than before, but still higher than abroad,and the gap between a specific data table. Process, the multi-material plastic molding die, efficient multicolor injection mould, inserts exchange structure and core pulling Stripping the innovative design has also made great progress. Gas-assisted injection molding, the use of more mature technologies, such as Qingdao Hisense Co., Ltd., Tianjin factory communications and broadcasting companies, such as mold manufacturers succeeded in 29 ~ 34-inch TV thick-walled shell, as well as some parts on the use of gas-assisted mould technology Some manufacturers also use the C-MOLD gas-assisted software and achieved better results. Prescott, such as Shanghai, such as the new company will provide users with gas-assisted molding equipment and technology. Began promoting hot runner mold, and some plants use rate of more than 20 percent, the general heat-thermal hot runner, or device, a small number of units with the world's advanced level of rigorous hot runner-needle device, a small number of units with World advanced level of rigorous needle-hot runner mould. However, the use of hot runner overall rate of less than 10%, with overseas compared to 50 ~ 80%, the gap larger. In the manufacturing technology, CAD / CAM / CAE technology on the level of application of a new level to the enterprise for the production of household appliances representatives have introduced a considerable number of CAD / CAM systems, such as the United States EDS UG Ⅱ,

电子信息工程文献专业英语中英互译

? . , . ? , a , a . , . ( ). a ( ). A . A . , , . : A " " . : a " " , a " " . "" . a 's . a " " 's . " " . ( ). . : a "" 's ; a "" a ; a "" . a , . a . 's , . a , a . , . A . , a . , , . Europe's a , a . a , ., . "'s a ," , , . " 's . 2002 . a ." , (), Toyota's 's 1, . 2010, a . . 2 , . , 's , . . , a Delphi , a a . " , , , ," . " ." Delphi '99. : , . . , . . " ," . , , Germany. "'s ." "

a ," , , , . a ( , , , ). . . , , a . $50 . Birmingham, England, 2000. 1995, Delphi, 7596 . 37 10 , . a . , a a , a , a , a a a . a a , a . , , . , , , . a , , , . , , a . : . . 电子动力转向系统 电子动力转向系统是什么? 电子动力转向系统是通过一个电动机来驱动动力方向盘液压泵或直接驱动转向联动装置。电子动力转向的功能由于不依赖于发动机转速，所以能节省能源电子动力转向系统是怎么运行？： 传统的动力方向盘系统使用一条引擎辅助传送带驾驶气泵，提供操作在动力方向盘齿轮或作动器的一个活塞协助驱动的被加压的流体。在电动液压的控制，一个电子动力方向盘包括一台电动机控制的一个高效率泵浦。由一个电控制器调控泵浦压力和流速来控制泵浦的速度，为不同的驾驶路况的提供转向。泵浦可以在汽车行驶低速时关闭以提供节能（在当代的世界市场上)。 电动控制转向使用电动机通过齿轮齿条机构直接连接以达到转向控制（无泵或液体）。多个电机驱动器和多驱动控制的实现是可能的。一个微处理器控制转向动态和驱动的工作。输入因子包括车速，转向，车轮扭矩，角度位置和转率。

外文翻译中英对照版

VOLUME 30 ISSUE 2 October 2008 Journal of Achievements in Materials and Manufacturing Engineering Copyright by International OCSCO World Press. All rights reserved.2008 151 Research paper 2008年十月期2卷30 材料与制造工程成果期刊 版权所有：国际OCSCO 世界出版社。一切权利保有。2008 ？？151研究论文 1. Introduction Friction stir welding (FSW) is a new solid-state welding method developed by The Welding Institute (TWI) in 1991 [1]. The weld is formed by the excessive deformation of the material at temperatures below its melting point, thus the method is a solid state joining technique. There is no melting of the material, so FSW has several advantages over the commonly used fusion welding techniques [2-10]. 1.导言摩擦搅拌焊接（FSW）是焊接学？会于1991年研发的一种新型固态焊接方法。这种焊接？是由材料在低于其熔点的温度上过量变形形成，因此此技术是一种固态连接技术。材料不熔化，所以FSW 相比常用的熔化焊接技术有若干优势。例如，在焊接区无多孔性或破裂，工件（尤其薄板上）没有严重扭曲，并且在连接过程中不需要填料、保护气及昂贵的焊接准备there is no significant distortion of the workpieces (particularly in thin plates), and there is no need for filler materials, shielding gases and costly weld preparation during this joining process. FSW被认为是对若干材料例如铝合金、镁合金、黄铜、钛合金及钢最显著且最有潜在用途的焊接技术FSW is considered to be the most remarkable and potentially useful welding technique for several materials, such as Al-alloys, Mg-alloys, brasses, Ti-alloys, and steels [1-16]. 然而，在FSW过程中，用不合适的焊接参数能引起连接处失效，并且使FSW连接处的力学性能恶化。However, during FSW process using inappropriate welding parameters can cause defects in the joint and deteriorate the mechanical properties of the FSW joints [2, 3]. 此技术起初就主要是为低熔点材料如铝合金、镁合金及铜合金而广泛研究的。The technique has initially been widely investigated for mostly low melting materials, such as Al, Mg and Cu alloys. 此技术已被证明是很有用的，尤其在连接用于航空航天用途的如高合金2XXX及7XXX系列铝合金等难熔高强度的铝合金。It has proven to be very useful, particularly in the joining of the difficult-to-fusion join high strength Al-alloys used in aerospace applications, such as highly alloyed 2XXX and 7XXX series aluminium alloys. 做出Al-5086 H32型板摩擦搅拌对焊的高强度、抗疲劳及断裂的力学性能？。The difficulty of making high-strength, fatigue and fracture resistant Mechanical properties of friction stir butt-welded Al-5086 H32 plate G. .am a,*, S. Gü.lüer b, A. .akan c, H.T. Serinda. a a Mustafa Kemal University, Faculty of Engineering and Architecture, 31040 Antakya, Turkey a 土耳其安塔卡亚31040，Mustafa Kemal大学建筑工程系 b General Directorate of Highways of Turkey, Ankara, Turkey b 土耳其安卡拉土耳其高速公路总理事会？ c Abant Izzet Baysal University, Faculty of Engineering an d Architecture, 14280 Bolu, Turkey c 土耳其Bolu 14280 Abant Izzet Baysal 大学建筑工程系 * Corresponding author: E-mail address: gurelcam@https://www.sodocs.net/doc/5513407490.html, *相关作者电子邮箱地址：gurelcam@https://www.sodocs.net/doc/5513407490.html, Received 30.06.2008; published in revised form 01.10.2008

仪表板外文文献翻译、中英文翻译、外文翻译

Dashboard From Wikipedia, the free encyclopedia This article is about a control panel placed in the front of the car. For other uses, see Dashboard (disambiguation). The dashboard of a Bentley Continental GTC car A dashboard (also called dash, instrument panel (IP), or fascia) is a control panel located directly ahead of a vehicle's driver, displaying instrumentation and controls for the vehicle's operation. Contents 1.Etymology 2.Dashboard features 3.Padding and safety 4.Fashion in instrumentation 5.See also 6.References Etymology Horse-drawn carriage dashboard Originally, the word dashboard applied to a barrier of wood or leather fixed at the front of a horse-drawn carriage or sleigh to protect the driver from mud or other debris "dashed up" (thrown up) by the horses' hooves.[1] Commonly these boards did not perform any additional function other than providing a convenient handhold for ascending into the driver's seat, or a small clip with which to secure the reins when not in use. When the first "horseless carriages" were constructed in the late 19th century, with engines mounted beneath the driver such as the Daimler Stahlradwagen, the simple dashboard was retained to protect occupants from debris thrown up by the cars' front wheels. However, as car design evolved to position the motor in front of the driver, the dashboard became a panel that protected vehicle occupants from the heat and oil of the engine. With gradually increasing mechanical complexity, this panel formed a convenient location for the placement of gauges and minor controls, and from this evolved the modern instrument panel,