搜档网
当前位置:搜档网 › Oil migration on single and two stage heat pump systems

Oil migration on single and two stage heat pump systems

Research programme on

ambient heat, waste heat and cogeneration

of the Swiss Federal Office of Energy

Oil migration on single and two stage heat pump systems Calibration tests and process design

Phase 1

Prepared by

Michele Zehnder (Ph.D.Student) and

Prof. Dr. D.Favrat

Laboratory of Industrial Energetics (LENI)

1015 Lausanne

on behalf of the

Swiss Federal Office of Energy

December 2000 Intermediate Report

Abstract

The subject of this project is to develop a high performance air water heat pump which is able to be introduced in the retro?t market.The system requirements of this market are heating temperatures of 65?C,at ambient temperatures descending until-12?C.To provide higher base performance ratings, the choice of the thermodynamic system is a two stage heat pump with economizer exchanger(see ?gure2.1).This type of heat pump has improved performances over a large range of application.For heat output adjustment it can be switched to different heating modes(single stage and two stage).For the two stage cycle,the lubri?cation of the compressors is a major aspect to be studied.

A new online measurement method is applied to evaluate the oil quantity which migrates through the cycle.The absorption spectre of the refrigerant-oil mixture is analysed with a Fourier Transform Infrared(FTIR)spectrometer and the oil quantity can be extracted with high precision(see?gure 6.3).(The analysis method has still to be re?ned.)The infrared spectrometers also allow to control the composition of the refrigerant mixture.A single capture of the spectre needs about30seconds. The measurements have to be referred to a regularly updated background spectre,which requests to vacuumize and clean the measurement cell.

The oil migration is simultaneously measured with a high precision densitymeter.The output signal allows a real time follow of the oil quantity and the transmitter will give reliable results after calibration over the application range.Any change of the refrigerant composition cannot be captured by the densitymeter.The resulting density shift would therefore not be attributed correctly to the amount of oil.

For the analysis of oil distribution in the whole heat pump,the measurement method to determine the oil level in the compressor crankcase,and the observation of the oil retention in the evaporator are also discussed in this project.

The heat pump design has been made,based on simulations of the thermodynamic cycle and using existing parts in the laboratory,such as the evaporator and the condenser.The design aim is to avoid oil trapping and to ensure oil transport in the vapour lines of the heat pump(see?gure4.1).

This report has been conducted by the Swiss Federal Of?ce of Energy.The author is responsible for the content and the conclusions presented in this report.

Note:Several?gures in this report have been updated from its original.

c 2001by Michele Zehnder

R′e sum′e

Le projet vise`a construire une pompe`a chaleur capable de pouvoir?e tre utilis′e e dans le march′e de remplacement de chaudi`e re.Dans ce contexte elle doit pouvoir fonctionner aux temp′e ratures jusqu’`a 65?C pour l’eau de chauffage et`a des temp′e ratures d’air qui descendent jusqu’`a-12?C.A?n de pou-voir fournir une puissance de chauffage plus′e lev′e e`a la temp′e rature de base,le cycle de pompe`a cha-leur choisi est un cycle bi′e tag′e`a′e changeur′e conomiseur(voir?gure2.1).Ce type de cycle montre des performances′e lev′e es sur un large domaine d’utilisation.Pour un meilleur suivi de la demande en puissance de chauffage,ce type de cycle peut fonctionner en mode mono′e tag′e ainsi qu’en mode bi′e tag′https://www.sodocs.net/doc/c710393920.html, lubri?cation des compresseurs doit?e tre′e tudi′e e pour le cas du fonctionnement bi′e tag′e. Une nouvelle m′e thode de mesure de la quantit′e d’huile`a′e t′e adopt′e e dans ce contexte.Le spectre d’absorption du m′e lange r′e frig′e rant-huile est analys′e par un spectrom`e tre infrarouge par transfor-mation de Fourier.Ce type de mesure permet d’extraire la quantit′e d’huile transitante`a travers la cellule de mesure avec une pr′e cision′e lev′e e(voir?gure6.3).(La proc′e dure de mesure est toujours en cours d’?e tre optimis′e e)En m?e me temps la mesure spectroscopique permet d’analyser la composition du r′e frig′e rant utilis′e.Une mesure prend cependant env.30secondes et le spectrom`e tre n′e cessite une prise de spectre de r′e f′e rence dans la cellule vid′e e et n′e toy′e e une fois tout les jours.

Un suivi de l’′e volution de la quantit′e d’huile migrante est cependant fait en parall`e le avec un den-sim`e tre`a haute pr′e cision.Une fois soigneusement calibr′e ce type de mesure permet un suivi sans maintenance ult′e rieure.Le densim`e tre seul ne permet cependant pas une mesure pr′e cise,car un chan-gement de la compostion du r′e frig′e rant n’est pas d′e tectable et serait attribu′e`a un changement de quantit′e d’huile.

Les mesures de niveau d’huile dans les enveloppes des compresseurs et la retention d’huile dans l’′e vaporateur permettront l’analyse globale de la distribution d’huile dans la pompe`a chaleur.Ces points sont′e galement discut′e s dans ce travail.

Le dimensionnement de la pompe`a chaleur`a′e t′e effectu′e sur la base d’une simulation du cycle thermodynamique et en consid′e rant des′e l′e ments existants au laboratoire(tel que l’′e vaporateur,le condenseur,...).Le design prend en compte d’′e viter au mieux les trappes d’huile et les tubes sont dimensionn′e s tel que le transport d’huile soit assur′e(voir?gure4.1).

Cette′e tude a′e t′e accomplie sur mandat de l’Of?ce F′e d′e ral de l’Energie.L’auteur est seul respon-sable du contenu et des conclusions.

Zusammenfassung

Ziel dieses Projektes ist die Entwicklung einer ef?zienten Luft/Wasser W¨a rmepumpe f¨u r den Sanie-rungsmarkt.Die daraus bedingten Systembedingungen sind Heizwassertemperaturen von65?C bei Aussentemperaturen bis–12?C.Um bei diesem Extrempunkt eine gen¨u gende Heizleistung erbrin-gen zu k¨o nnen,f¨a llt die Wahl auf einen zweistu?gen W¨a rmepumpen-Kreisprozess mit Economizer W¨a rme¨u bertrager(siehe Abb.2.1).Dieser Kreisprozess zeichnet sich in erh¨o hten Leistungskennzah-len,auf einem breiten Anwendungsbereich aus.Um eine Anpassung der Heizleistung zu erm¨o glichen, kann der Prozess in verschiedene Heizbetriebsarten umgestellt werden(einstu?g,zweistu?g).Beim zweistu?gen Betrieb ist die korrekte Schmierung der in Serie geschalteten Kompressoren ein noch ungel¨o stes Problem und wird in diesem Projekt n¨a her untersucht.

Eine neuartige Messmethode zur Bestimmung des im Kreisprozess mitgef¨u hrten¨Olanteils wird vor-geschlagen und getestet.Diese Methode beinhaltet Messungen von Absorptions-Spektren des¨Ol-K¨a ltemittelgemisches mittels eines Fourier Transform Infrarot(FTIR)Spektrometers.Daraus kann der ¨Olanteil mit hoher Pr¨a zision bestimmt werden(siehe Abb.6.3).(Die Messmethode muss noch verbes-

sert werden.)Mit Hilfe des Spektrometers kann auch die Zusammensetzung des K¨a ltemittelgemisches (R407C)jederzeit¨u berpr¨u ft werden.Eine Messung dauert ca.30Sekunden.Die Messergebnisse wer-den mit einer Referenzmessung(Background)verglichen,welche regelm¨a ssig durchgef¨u hrt werden muss.Dabei muss die Messzelle jedesmal vakuumiert und gereinigt werden.

Gleichzeitig kann der¨Olanteil mittels eines pr¨a zisen Dichte-Messgwertgebers ermittelt werden.Die hohe Zeitau?¨o sung der Messungen erm¨o glicht eventuelle Schwankungen mitzuverfolgen.Einmal ge-eicht,funktioniert dieser Messwertgeber mit hoher Zuverl¨a ssigkeit und ohne Wartungsarbeiten.Die Messung der Gemischdichte kann hingegen nicht in jedem Fall auf den¨Olanteil zur¨u ckgef¨u hrt werden. Eine Konzentrationsverschiebung des K¨a ltemittels w¨u rde dann einen Auswertungsfehler verursachen. Um eine Bilanzierung der¨Olverteilung in der W¨a rmepumpe zu erm¨o glichen,ist eine genaue Messung des¨Olstandes in den Kompressoren vorgesehen.Die R¨u ckf¨u hrung des¨Ols aus dem Verdampfer wird ebenfalls speziell analysiert.

Die Auslegung der Versuchsw¨a rmepumpe wurde mittels einer Simulation des thermodynamischen Prozesses durchgef¨u hrt.Verschiedene bereits vorhandene Elemente werden in die neue Anlage inte-griert(Verdampfer,Kondensator,...).Das Design ist speziell auf die Bed¨u rfnisse beziehungsweise auf den¨Oltransport und die¨Olmigration angepasst(siehe Abb.4.1).

Diese Arbeit ist im Auftrag des Bundesamtes f¨u r Energie entstanden.F¨u r den Inhalt und die Schlussfolgerungen ist ausschliesslich der Autor dieses Berichtes verantwortlich.

Contents

Abstract (i)

R′e sum′e (ii)

Zusammenfassung (iii)

1Introduction1 2Thermodynamic concept3

2.1One stage heating mode (5)

2.2Two stage heating mode (5)

2.3Defrosting mode (5)

3Simulation7

3.1Thermodynamic cycle (7)

3.2Performance prediction (8)

4System design9

4.1Refrigerant and oil (9)

4.2Components (9)

4.3Heat pump layout (10)

5Measurement methods13

5.1Densitymeter:Bopp&Reuther DIMF2.0TRV (13)

5.2FTIR:Nicolet Magna-IR560 (14)

5.3Level detection:Visual level caption on a bypass tube (15)

5.4Flow transmitter:Coriolis K-Flow (15)

5.5Oil retention in Evaporator:Separating loop and balance (16)

6Calibration loop for oil migration17 Bibliography21 A Appendix1

A.1FTIR spectres of the principle components (1)

A.2Calibration of the Radar Emittor VEGAPULS (2)

A.3List of components (3)

A.4List of measurement points (4)

1

1.Introduction

The two oil crisis in the1970s were the?rst initiators of heat pump selling world wide.In the1980s the number of new installed units in Europe diminished again because of the reduced oil price and the lack of technical support of the?rst generation of the products.Since the late1990s the market share of the heat pump units grows again continuously.The second generation products are more reliable and several political efforts,introducing quality labels for the products,the manufacturers and the contractors,prevent a new breakdown of the selling.

The European heating market requires mainly heating only heat pumps for residential heating.High performance components are available for new buildings with moderate heating water temperatures. Heat pumps being able to replace oil burners are not yet available.The main improvements for this application type to be made are:Providing base heating power for the very cold period in winter and ensuring high heating water temperature for the radiator type of heat distribution.Both conditions can be met by implementing a two stage heat pump cycle,which will be studied in this project.

The lubrication system of the compressors has to be reconsidered,for long term functionality of two stage systems.Oil migration will be in this context the most important phenomenon to be studied. The oil migration is measured by a high precision densitymeter and is coupled to a infrared spectrom-eter.The online measurement of the oil amount circulating in the refrigerant loop allows to study the mechanisms of oil transport and to follow oil migration in non steady state conditions,e.g.during the defrosting mode.

2 1.INTRODUCTION

3

2.Thermodynamic concept

The choice of the proposed two stage heat pump cycle is based on the experience collected at LENI over several projects until present.It has been shown,that only this type of cycle results in a real improvement of the performances over the whole range of application,see

[5].Other possibilities of enlargement of the application range are represented by the vapour injection compressor type [1],or the subcooling toping cycle [9].Oil migration problems however concern only the two stage cycle and will be studied hereafter.The migration phenomenon is analysed and modelled for one stage and two stage con?guration of an experimental heat pump unit.

The heat pump cycle is represented by the schema in ?gure 2.1.

Figure 2.1:Schematic representation of the two stage heat pump cycle

All the possible test con?gurations of the heat pump are shown in the following ?gures.Pressure levels are represented in different colours,dashed lines represent the part of non circulating ?uid.

4 2.THERMODYNAMIC CONCEPT

(a)one stage

heating

(b)two stage

heating

(c)defrosting

Figure 2.2:Heating modes and defrosting

2.1.ONE STAGE HEATING MODE5 2.1One stage heating mode

Bypassing the HP compressor,the hot gas at the outlet of the compressor is directly injected into the condenser.The condensed refrigerant?ows through the economizer without any heat exchange and passes through the suction line overheater.The two phase?ow is evaporated and then overheated before entering the compressor.Due to the high discharge temperature,the operational domain is limited.

2.2Two stage heating mode

Using the two stage con?guration with the economizer,the maximum system temperature is lowered and can be controlled by the injected?ow amount.After the condenser the refrigerant is subcooled in the economizer before being divided.The minor?ow is expanded to the midstage pressure and reenters into the economizer.Fully or partially evaporated it will be remixed with the hot gas from the LP compressor and then enters into the HP compressor.The main refrigerant stream?ows through the overheater exchanger.After the main expansion valve it will be evaporated before rejoining the?rst stage compressor.

2.3Defrosting mode

The defrosting of the evaporator is initiated by the reverse cycle valve.The hot gas of the LP com-pressor outlet is directly injected into the evaporator in the inverse sense.The condensed refrigerant is circulating through a bypass line with a manual expansion valve.In the condenser the refrigerant is heated up and evaporated by the heating water,using the thermic inertia of the heating water.

6 2.THERMODYNAMIC CONCEPT

7

3.Simulation

3.1Thermodynamic cycle

The simulation of the thermodynamic behaviour of the heat pump is based on the considerations made on earlier projects of this topics (see [8]).The two stage heating mode is represented on the log P -h diagram in ?gure 3.1.

150200250300350400450500

5

1015

20

25

30

enthalpy [kJ/kg]p r e s s u r e [b a r ]Figure 3.1:Thermodynamic cycle

This diagram is issue from a simulation of the heat pump in heating mode at air inlet temperature at 0?C and heating water outlet at 50?C.

8 3.SIMULATION 3.2Performance prediction

For the application range which corresponds to an retro?t heating case(heat distribution on radiators and air source heat pump)the simulated COP for the two stage mode is

COP heating=2.61eta II,th=56%

Heat output=9328[W]PR1=2.81

El.input=3575[W]PR2=3.56

Tmax=91.79[?C]Pcond=25.31[bar]

mass?ow1=31.3[g/s]mass?ow inj=18.0[g/s]

Table3.1:Performance values at A-12/W60

COP heating=3.75eta II,th=58%

Heat output=11886[W]PR1=2.26

El.input=3167[W]PR2=2.22

Tmax=71.14[?C]Pcond=20.11[bar]

mass?ow1=48.5[g/s]mass?ow inj=14.3[g/s]

Table3.2:Performance values at A0/W50

The indicated performance does not include any auxiliary power(ventilator,solenoid valves,water pump).The experimental COP is expected to be about10%-25%lower than the ideal simulated value when both,auxiliaries and defrosting have to be included.

9

4.System design

4.1Refrigerant and oil

Refrigerant used is R407C(R32/R125/R134a[0.23/0.25/0.52by w.])Lubricating oil is EAL Arctic 22CC(polyolester especially for Copeland produced and delivered with Copeland compressors).The refrigerant and oil amount will be determined when the physical test rig is constructed.

4.2Components

The oil migration test utility is composed by the following principal components:

?compressor LP:Copeland Scroll ZR49,3-phase

The nominal suction volume rate at50Hz is11.7m3/h.Optimum performance is reached at low volume ratios(VR?=2.5).

?compressor HP:Copeland Scroll ZR28,monophase

The high stage compressor is of the same type,but with lower nominal suction volume(6.83m3/h).

?condenser:Alfa Laval CB50-30H

This is a brazed plate condenser with heating water in counter?ow con?guration.Total heat exchange area is1.5m2.

?economizer:Swep B8x10HP

The economizer is a brazed plate heat exchanger with an exchange surface of0.184m2.After being expanded to the midstage pressure level,the injection?ow is partially evaporated and then remixed with the hot gas at the outlet of the LP compressor.

?expansion valves:Egelhof RTC1.0and RTC0.5

For the research project two electronic expansion valves are implemented to regulate indepen-dently the mass?ow on both stages.

10 4.SYSTEM DESIGN

?evaporator:Alfa Laval-Artec2510E32TR6R800A

The evaporator is an?nned tube air evaporator with24circuits and8passes.The?n pitch is

3.6mm.The frontal surface of the air circuit is0.8x0.8m2.The total exchange surface on

the refrigerant side is4.58m2.The tubes are enhanced surface copper tubes with an internal diameter of9.5mm and the?ns are of aluminium with a thickness of0.2mm.

?suction line overheater:Packless HXR75

The suction line overheater is integrated for optimizing the evaporator?lling and to avoid evap-oration pressure drop due to the temperature glide of the refrigerant mixture.The requested overheat in the compressor is reached in the overheater and liquid?ashes are avoided to en-ter the compressor.It is a concentric countercurrent heat exchanger with an internal exchange surface(on the gaseous side)of0.0175m2.

?reversing cycle valve:Ranco V6-2103

This valve enables a reversed cycle defrosting.Only the LP compressor is used for the defrost-ing period.A hand regulated piston valve is situated on the defrosting bypass line after the evaporator.

4.3Heat pump layout

The planned two stage heat pump has been developped virtually on a3D design program.This has been done to optimise volume,pressure drops and to build a compact unit.

The front view from the heat pump unit without the oil distribution lines and the measurement devices is represented in the?gure4.1.

A detailed list of the components and a cost overview is given in the appendix.

4.3.HEAT PUMP LAYOUT11

Figure4.1:Heat pump layout frontside

12 4.SYSTEM DESIGN

13

5.Measurement methods

All the measurement points of this unit are represented in the schematic representation of the heat pump unit in

?gure 5.1.

Migroil: two-stage air-water heat pump

2510E32TRGR800A3,6P24NCAL PT:503,504Figure 5.1:two stage heat pump cycle

To measure the oil migration at high precision,a densitymeter will be coupled to an Fourier Transform Infrared Spectrometer.By a calibration loop the measurement devices are compared.5.1Densitymeter:Bopp&Reuther DIMF 2.0TRV

The densitymeter is a high precision transmitter with the following indicated performance:Reproducible measurement precision:<±0.02%(±0.2kg/m 3)

For the mean running point refrigerant at 40?C and at 10K subcooling the relative densities are:rho R407C =1073.0kg/m 3

rho oil POE =980kg/m 3

Mixing 2homogenuos substances (in this example w oil of oil is mixed with (1?w oil )of refrigerant),

14 5.MEASUREMENT METHODS the speci?c volumeνof the mixture is given by:

ν0mix=w oilνoil+(1?w oil)νre f r(5.1) The density of an ideal mixture can be therefore be written as:

ρ0mix=

1

w oil

ρoil

+1?w oil

ρre f r

(5.2)

The effectif mixture volume can diverge from the ideal value and the difference between the real value and the theoretical one can be evaluated by the calibration of the densitymeter.

νE=νmix?ν0mix=f(T,p)(5.3) By the measurement of the mixture densityρmix the oil weight can be calculated with

w oil=

1

ρmix

?νE?1

ρre f r

1

ρoil

?1

ρre f r

(5.4)

Supposing that the density of the pure components and the excess volume are perfectly known for the examined domain,the incertitude of the measurement of the mixture density by the densitymeter is traduced in the value of the oil weight as follows:

d(w oil)=

ρre f rρoil

ρre f r?ρoil

1

ρ2mix

d(ρmix)(5.5)

With a measurement precision of the densitymeter of±0.2kg/m3the absolute precision of the oil weight prediction is about±0.2%.

Errors in the correlations used for the pure components ar not taken in account.For this application the error on the refrigerant density is directly traduced into the incertitude of the oil weight dissolved in the refrigerant.

Shifts in the refrigerant composition will greatly in?uence the incertitude and therefore a online control of the composition has to be included into the study.

5.2FTIR:Nicolet Magna-IR560

The Fourier Transform Infrared(FTIR)spectroscopy allows to make online measurements on the refrigerant composition and of the oil weight dissolved in the liquid refrigerant.Measurements can be taken every30seconds.The measuring cell is composed by a ATR single re?ection diamond, covered by a cylindrical volume.The light source of the spectrometer is liquid nitrogen cooled and

5.3.LEVEL DETECTION:VISUAL LEVEL CAPTION ON A BYPASS TUBE15 the envelop of the spectrometer is purged with cleaned and pressurized air?ow(?ow rate about700 l/h,to be improved).

The spectra of the pure oil and the refrigerant were measured to determine the main absorption peaks. (See graphs in the Annex of this report)

EAL Arctic22CC:1020,1120,1150,1220,1370,1470,1740,2850,2920,2950cm?1

R407C:660,960,1060,1180,1300cm?1

The interpretation of the different vibrational modes represented by the absorption peaks is not easy and requires good experience in the domain.The author is reffering on several publications where additional information can be found,see[4],[6]and[2].Web databases are very helpful as well for the main informations,[7].The superposition of the two?uids shows a free peak at1740cm?1for the oil spectre and the precision of measurement for the oil mass fraction is evaluated at0.1-0.2%. See calibration test results for further informations.

The composition of the R407C refrigerant has to be analysed by deconvolution of the absorption stectrum into its components parts.The calibration tests have to be performed for several couples of temperature and pressure,representing the running conditions in the heat pump cycle.

This additional measurement device allows to make precise analysis on the composition of the refrig-erant,which will be the fundament for a precise analysis of the measures with the https://www.sodocs.net/doc/c710393920.html,ing a ternary refrigerant mixture like R407C,a composition control is requested.Additional costs occured in buying a ATR re?exion cell,as the FTIR spectrometer is already property of the laboratory.

5.3Level detection:Visual level caption on a bypass tube

To know how much oil is accumulated in the compressor shaft,the oil level has to be measured with high precision.A transmitter will be used separately for each compressor.

Different measurement techniques were considered for level detection.After analysis of the test con-ditions(namely low ratio of the dielectric constant between the gas phase and the liquid),the capacitif and the radar measurement techniques have been rejected.(A radar transmitter has been tested with a precision of±5mm).The only reliable technique with expected measurement precision of±1mm is the capture of the level by a camera and the picture can be treated with software(online).

5.4Flow transmitter:Coriolis K-Flow

The mass?ow is measured by two coriolis transmitter.The mass?ow is measured very precisely by phase detectors mounted on the vibrating metering tubes.The mass?ow ranges for the two available models in the laboratory are K20:0-9kg/min and K100:0-45kg/min.The operating conditions are T(-95?C/180?C)and p(150bar/limiting pressure by?anges25or40bar).The cross section of the vibrational tube is K20:0.174cm2and K100:0.9423cm2.

Zero stability Z is done at K20:0.0018kg/min and K100:0.009kg/min.The accuracy of the mass

会议系统介绍

会议系统 会议系统包括:基础话筒发言管理,电子表决功能,脱离电脑与中控的自动视像追踪功能,资料分配和显示,以及多语种的同声传译。它广泛应用于银行、公安、部队、学校、铁路、航空、电力等单位。 基本纯讨论会议系统 最基本的纯讨论会议系统,由会议主机、会议单元、功放、音响,这几部分组成。此系统为最基本的会议系统,适合用于只需要会议讨论的场所。会议单元可以是有线手拉手的方式连接或者是无线的方式。 图1为手拉手方式: 图1 视像追踪 在讨论系统的基础上还可以进一步提升应用,就是通过摄像快球来实现视像追踪功能。 在一人一机的情况下,实现会议讨论功能,与会代表按下发言键便可以发言。当与会代表开启话筒时,摄像机会自动跟踪到发言者所在的位置,连接视频显示设备可将摄像机所摄图象显示出来。(图2)

同声传译 同声传译又名即时传译,顾名思义,是指基本同步的语言翻译。翻译工作由翻译员负责完成,同声传译设备只是提供操作的界面。换言之,配备同声传译设备后,这些设备组成的系统并不能对语言执行自动翻译,必须由传译员翻译。 当说不同语言的人会面,或召开国际性会议时,由于双方或者多方语言无法沟通,必须由翻译员进行沟通。这时就需要一套同声传译设备,每位代表佩带一副接收器和耳机选听,不管发言的代表是何种语言,都基本有一个与之对应的翻译员作出指定语言的翻译,这就是同声翻译设备的作用。 同声传译系统的核心技术是多语种旁听信号的传输(分配、发送与接收),主要由有线与无线两种方案构成,而无线传输又分为电磁波方式和红外线方式两种。 图3为模拟传输方式: 图3

红外线传输技术 红外线传输由于具备安装简单、音质良好、保密性强等优点,普遍应用在同声传译的语言分配与传输领域。采用红外传输的同声传译系统基本上由以下器材或子系统组成。 图4所示为红外线同声传译的典型系统图 图4 表决系统 在会议中我们需要一套表决系统,在会前可以作为参会人员签到、在会中可以对问题进行投票和表决,体现了民主、公平、公正、科学的原则。 图5为带表决的会议单元: (桌面式)(嵌入式) 图5 图6为整个会议系统系统图:

会议系统简介

I SMART 智能审图及远程互动审图一体机 秦工是一位资深的高级工程师,参加工作20多年来,一向以严谨认真、兢兢业业,在建筑设计院享有极高的声望。在设计院里年轻人都流传着一个段子,意思是说做设计师太辛苦,每天的生活都塞满了枯燥的设计图纸,仰着头那是在看投影,平着看那是在看电脑,低着头那是在看图纸,侧着眼看那是在看秦工。 每次跟秦工开这个玩笑时,秦工总是笑笑表示理解:虽然说现在用电脑用投影机代替了从前的手工作图,效率要高得多。但遇到投影显示不清楚,或者远远看着投影幕布说不明白,尤其是投影幕前无法批注圈点和保存文档,还得从成堆的图纸中翻出来指出存在的问题,精力的耗费在所难免。负责异地工程设计项目时,频繁的出差耗费了大量的时间和精力,旅途劳累加上繁重的工作任务更是让人身心疲惫。特别是见到一些设计师年纪轻轻患上严重的颈椎病或视力严重减退感到特别痛心。 一次偶然的机会,秦工见到英特智讯公司的智能审图及远程互动审图产品,它创造性地解决了图纸高清晰度显示、大幅面图纸快速调用、在屏幕上直观缩小放大以及拖动等问题,而且能够在图纸上直接手写标注,修改等,一键启动远程数据会议系统不仅能为远程审图的各方提供流畅的音视频,还能通过共享图纸和实时显示对图纸的操作实现远程互动交流,特别适用于建筑图纸讨论与评审,就推荐到建筑设计院使用。经过简单的培训,设计师们很快就能够熟练的操作和使用,轻松审图和人性化的功能设计让设计师们的日常工作轻松了很多。单调沉闷的环境一去不复返,建筑设计院里开始充满着年轻活跃的氛围,不知不觉之间,先前在年轻人中间流传地那个段子慢慢地被人忘记了。 I SMART智能审图及远程互动审图一体机(以下简称一体机)为何如此"神奇"?它到底怎样解决图纸审看和会议沟通的障碍问题?谈到这个问题时,秦工饶有兴致地说起了一体机的应用实例,脸上洋溢着满意的神情。

多功能会议系统(一类特选)

品目五多功能会议系统 5.1 概述 花园大厦作为一座高档次的综合性多功能的大厦,在东阳市以后的发展中将扮演重要的角色,许多重要的决策和会谈将会在这里进行,所以一套好的会议系统是会议顺利进行的必要保证。 花园大厦会议系统为业主提供从事于重要会议的高级会议中心。智能会议系统将高质量的音频、视频和诸多智能特性紧密结合在一起,通过数字信号处理、压缩编码技术和数据传输等新技术的融入,实现更多、更齐全的电话会议、视频传输、信息传输功能。 电子会议系统是在计算机软、硬件的支持下,将各种会议系统及相关设备如:数字会议系统、扩声系统、视频显示系统、计算机网络系统、会议灯光系统等有机地集成在一起,形成的一个完整的系统。该系统实现了自动化的集成控制功能,并可通过计算机网络调用数据库中的各类数据和图像等信息,从而给与会者以声图并茂的视觉和听觉效果,更好的营造了会议的氛围,提高了会议效率,也方便了与会领导的决策。同时,考虑到东阳市国际性商务活动的发展,该会议系统要求实现同声传译工程。为花园大厦举行各种电子会议、高层会议、技术研讨甚至国际性会议等提供不同的会议环境。 5.2 需求分析 整个花园大厦共有大型会议室1个、小型会议室4个。 综合二层设置6席带同声传译功能讨论性数字会议系统;图像显示系统;会议音响系统;中央控制系统;会议摄录系统;视频会议系统,可举行国际性会议、一般大型会议、与上级政府或其他部门一起举行视频会议。 5个小型会议室设置一套简易会议系统;可移动多媒体系统(扩声和音源设备),主要用于小型会议讨论等。 本系统具备适当的超前性,可以适应不同规模和性质的会议接见。设计可以进行6个语种的同声传译的国际会议接待功能,能与其他远程会场召开远程视频会议(电视、电话会议系统)。 各会议室的具体功能: 功能 综合三层100人 会议室 综合三层50人 会议室(南) 综合三层50人 会议室(北) 综合十五 层会议室 综合十六 层会议室数字会议系统√(同传、发言) 大屏投影系统√√√√√ 会议扩声系统√√√ 中央控制系统√ 会议摄录系统√ 视频会议系统√ 投票表决系统√ 同声传译系统√ 5.3 设计依据 《厅堂扩声系统声学特性指标》GYJ25-86 《剧场建筑设计规范》JGJ57-2000,J67-2001 《厅堂扩声特性测量方法》GB/T4959-1995 《声系统设备互连的优选配接值》GB14197-93 《客观评价厅堂语言可懂度的RASTI法》GB/T14476-93 《厅堂混响时间测量规范》GBJ76-84 《民用建筑电器设计规范》JGJ/T16-92 5.4 系统架构 5.4.1 综合三层大型会议室系统设计 5.4.1.1 数字会议系统 在一个专业的会议系统中,数字化会议系统是一个可供主席和代表分散自动或集中手动控制传声器的单通路声系统。在这个系统中,所有参加讨论的人,都能在其坐位上方便

(会议管理)视频会议系统说明

视频会议系统概述 视频会议系统(Videoconferencing System)是一种以视频为主的交互式多媒体通信,它利用现有的图像编码技术,计算机通信技术以及微电子技术,进行本地区或远程地区之间的点对点或多点之间的双向视频,双工音频,以及数据等交互式信息实时通信。视频会议的目的是把相隔多个地点的会议室电视设备连接在一起,使各方与会人员有如身临现场一起开会,进行面对面对话的感觉,因此广泛地应用于各类行政会议,远程培训、科技会议、远程教学以及商务谈判等场合中。视频会议系统具有真实、高效、实时的特点,是一种简便而有效的用于管理、指挥以及协同决策的技术手段,在国内各行各业尤其是政府各部门已开始广泛采用,并已发挥出巨大的效益。 视频会议的应用 1).政府级会议 2).商务谈判 3).紧急救援 4).作战指挥 5).银行系统 6).远程教育 7).远程医疗 1.系统介绍 多点控制单元MCU 多点控制单元MCU(Multipoint Control Unit),是多点会议电视的汇接

中心,多点会议电视通过MCU来实现音频和视频的混合与切换以及会议共享数据的交换,BYQ-BORYARD MCU-8000系列为标准1U机架式产品,可以方便的放置于网络设备室。 嵌入式会议室终端 系统参数 ?完全符合TCP/IP技术标准 ?同时支持8-100路终端接入 ?同时可进行8个独立会议 网络参数 ?内置10M/1000M自适应网络接口 ?低带宽用户支持,每用户带宽上载500K下载1M,可达25F/S ?支持DHCP 功能 ?支持会议控制 ?支持会议密码保护 ?支持单画面、多画面模式切换,根据语音能量有选择的进行混音

会议系统简介

会议系统(摘录) 会议系统 会议系统包括:基础话筒发言管理,代表人员检验与出席登记,电子表决功能,脱离电脑与中控的自动视像跟踪功能,资料分配和显示,以及多语种的同声传译。它广泛应用于监控、指挥、调度系统、公安、消防、军事、气象、铁路、航空等监控系统中、视讯会议、查询系统等领域,深受用户的青睐。 会议系统设备构成 基本会议系统 会议主机SV-M800B 最基本的会议系统,由麦克风、功放、音响,这几样设备的组合应用也可以说是一个会议系统了,它们起到了传声,扩声的作用。 现代会议系统 随着科技的发展、功能需求的提升,特别是电脑、网络的普及和应用,会议系统的范畴更大了,包括了表决/选举/评议、视像、远程视像、电话会议、同传会译,这些是构成现在会议系统的基本元素,同时衍生了一系列的相关设备,比如中控、温控制、光源控制、声音控制、电源控制等等。现代科技发展的促使下,会议系统定义成是一整套的与会议相关的软硬件。

会议系统的发展史 原始的会议形式: 远古的部落氏族会议,就是把大家召集到一个空旷的地方共同讨论一些重要的事情,受 SV-M880B 条件限制,会场中不可能配备类似现代会场中的任何电器设备,这样的会议形式历经原始社会、奴隶社会、封建社会,几乎占据了人类发展的整个历史过程。设备空白的会议形式严重的影响了大型会场中人与人之间的沟通与交流。 第一代会议系统: 会议话筒SV-M801 工业革命以后,科技的进步使电子技术有了突破性发展。会议的组织形式变成多只话筒一字排开同时接入现场的电声设备,与会者通过电声设备获取信息,只是会议讨论时,你一句我一句,特别是某些大型会议,会议的组织很难有序的进行。 第二代会议系统:

无线智能会议系统功能介绍

WICS无线智能会议系统 一、概述 1、会议系统的现状 目前,在会议系统方面有传统的投影机+中控+矩阵多媒体系统,针对上述的传统会议系统,我们发现会议系统往往造价不菲,在原有的会议场景中改造难度大,如:铺设线路难度大,位置固定不能更改,不能随意增添数量等等。不能支持目前流行普及的智能手机、平板电脑流畅的无线化投影。 2、智能会议的发展趋势 由于笔记本电脑的广泛应用,智能手机、平板电脑(Android系统、苹果系统)的普及,平板电脑的携带方便,手写触控是公认的优势,会议模式将不得不考虑这些移动设备的配套应用,然而wifi是一个最好的连接方式。 二、无线智能会议系统的优势 1、一体化的设计,创造性的将无线投影技术、电源远程控制技术和大屏显示设备结合在一起,使整个系统不仅功能丰富,使用也特别简单。 2、大大降低会议系统的构建成本,通过wifi模式支持更多移动设备的介入,增加特色应用,提升会议质量与效率。 三、无线智能会议系统的功能介绍 1、支持智能手机、平板电脑(Android系统、苹果系统)通过无线wifi的方式把图像同步投影到显示设备(投影机、液晶电视)上,最高支持1080P的高清分辨率,最多接入数高达128个(微软win7/win xp/win 8的系统更可支持影音同步); 2、IE页面浏览的会议控制模式,让主持人能通过电脑、平板甚至手机都可以轻松掌控客户端的投影权限; 3、配合高端的智能手机、平板电脑,可以实现高清的现场抓拍,即时批注;通过高清的现场摄像,可以提升会议的效率; 4、符合TCP/IP网络接入协议,能简易融入各种校园网及企业网,企业云等各种网络系统,让各种设备都能通过一个wifi也能实现一边上网一边无线投影; 5、支持四种不同方式(讲台电脑本地操作、无线鼠标键盘控制电脑、电子白板控制电脑、平

(会议管理)综合会议管理系统介绍

...../ ?更多资料请访问.(.....) ...../ 1.1 MCU设备技术要求RMX512C 1)基本要求 ?MCU采用一体化化的体系结构,满足电信级7×24稳定性、可靠性及冗余电源能力; ?支持H.323标准,支持SIP协议。 ?MCU必须支持推荐的标清终端及高清终端的混合进入同组会议,且可以保证高清及标清在会议中混合而不会降低系统容量。 ?MCU完全支持H.323,单台MCU必须可以支持12个4M视频端口系统容量。 ?可支持软件终端加入会议,并支持软件终端通过软件发送电脑图像到各会场。 ?具有较高的可靠性,MTBF为10万小时。 2)视频要求 ?视频编码支持ITU的H.26l、H.263、H.263+、H.264。 ?支持ITU-T标准的H.239双流标准。 ?实况视频分辨率可以支持QCIF、CIF、2CIF、4CIF、720P、1080P。 ?双流分辨率以支持VGA、SVGA、XGA、720P。 ?支持任意音频协议、视频协议、图像格式、速率接入同一个会议; ?支持N+1分屏模式,支持16分屏,满足24种分屏的布局模式; ?发送双流情况下,主视频流依然保持1280×720p的分辨率。

3)音频要求 ?音频编码支持G.711、G.722,、G.723.1C、G.728、G.719(siren 22)等。 ?用户及管理员静音控制 ?设备应该支持纯语音终端接入会议的能力。 4)管理要求 ?MCU的管理系统应采用专用的管理软件(非WEB方式),并实现全中文的管理方式。 ?支持语音激励模式、演讲者模式、导演模式、轮询会议。 ?支持远端镜头遥控FECC功能。 ?MCU应支持会议通过密码设置保证会议的安全和独立。 ?支持能够显示中文会场名及中文滚动字幕。 ?支持终端发起会议 ?支持会议主席在会场进行会议的控制,比如静音其它会场,以及结束会议等管理手段; 5)安全要求 ?AES加密 ?分级许可管理 6) 容量与速率 ?MCU容量不受分屏、速率、混协议的影响, ?H.323最大速率可达4M; ?支持高标清在同一会议,以满足将来系统扩展需要。 ?支持视频与音频1:1备份。 7)其它要求 ?可安装于19寸标准机柜。 ?MCU支持网络纠错补偿技术,保障在5%丢包情况下会议的效果。 ?MCU具备2个以上网络接口,支持跨网段会议。 ?MCU支持DiffServe、IP优先级,动态抖动缓冲器,语音及视频差错消隐技术的

会议系统操作说明书

一、操作说明 1.1、音响系统 1.1.1音响设备开、关机顺序 打开设备,打开电源时序器;关闭系统,关闭电源时序器。 1.1.2功能操作 1、会议时 1.打开设备,把功放旋钮旋到最大; 2、把调音台的输出推子(L、R)推到0DB; 3、根据使用的话筒,把对应的调音台输入通道打开(如有需按下“ON”键)如果使用会议话筒需要把幻想电源开关“POWER+48V”打开。 4、把这路通道推子推到需要的声音响度,但是不能超过0DB,一般在-5DB ——0DB之间,请把这个推子旁边的编组开关打开; 2、播放音乐 1.打开设备,把功放旋钮旋到最大; 2、把调音台的输出推子(L、R)推到0DB; 3、如果播放DVD,把DVD片子放进去,按下播放键,把对应的调音台输入 通道打开(按下“ON”键) 4、把这路通道推子推到需要的声音响度,但是不能超过0DB,一般在-5DB ——0DB之间,请把这个推子旁边的编组开关打开; 3、录音 1.打开设备; 2、把调音台的输出AUX2(在调音台的右边)旋到0DB; 3、把需要录音的话筒通道对应的AUX2旋到-5DB——0DB之间,这样就把这路话筒进入录制了。 4、远程视频会议

1.打开设备,把功放旋钮旋到最大; 2、把调音台的输出AUX1(在调音台的右边)旋到0DB; 3、把远程视频会议这路通道推子推到需要的声音响度,但是不能超过0DB, 一般在-5DB——0DB之间,请把这个推子旁边的编组开关打开; 4、把需要送给远方的话筒通道对应的AUX1旋到-5DB——0DB之间,这样就把这路话筒进入远程视频终端了。 5、注意:不能把远程视频这路的AUX1旋钮打开。 1.2、大屏显示系统 1、打开大屏设备电源; 2、通过无线触摸屏的把大屏打开; 3、通过无线触摸屏选择大屏需要的模式; 4、通过无线触摸屏选择大屏需要的信号输入; 5、注意:如果大屏模式不能调用,请动一下大屏控制电脑的鼠标就可以了; 1.3、矩阵切换系统 1、通过无线触摸屏选择信号的输入输出; 2、如果要把视频信号切换到桌面液晶显示器和控制室的六台监视器,首先通过无线触摸屏的AV矩阵界面把需要显示的视频信号切换到倍线器,再到VGA 矩阵界面把选择的倍线器信号切换到监视器和桌面液晶显示器上即可; 1.4、数字会议和摄像跟踪系统 1.4.1数字会议系统 按下电源开关后,HCS-4100MA/05 会议系统主机上电自动初始化,然后进 入 LCD 初始界面,这包括“菜单”、“开机数量”和“模式”,如下左图所示。此时,按“”键可改变开机数量,按“EXIT”可切换模式。 按“菜单”下的 MENU 键进入菜单设置界面,这包括“网络设置”、“同传设置

会议室设计说明.

第一部分总体介绍及概念性说明 一、工程设计思想 作为一个完善的多功能会议系统的解决方案,不仅要有优质的会议系统设备,在系统功能扩充上还需要结合诸如 DVD 、录音卡座、投影机、大屏幕图型处理器等多媒体设备,同时也需一个强大的中央控制系统来管理和协调各种设备的动作。 本次会议系统工程项目设计范围包含一个约 120平米高级智能多媒体会议厅会议系统设计。本次设计,我们主要是根据多年的施工经验, 为本会议厅堂作一个比较明确的规划。针对会议室进行会议、音频、视频、摄像、录音录像及远程会议系统设计,实现会议室的多媒体会议功能,满足简洁流畅的会议过程、逼真传神的听觉效果、清晰舒适的视频显示、智能的摄像跟踪、完整的会议记录、方便快捷的远程会议等要求。整个系统大致分为显示与监视、拾音与扩声、信号传输与控制摄像照明灯光、电视电话会议等五个部分。由大屏幕显示、液晶显示、音响、视频监视录像、多媒体音视频信号源矩阵切换和中央集成控制、摄像照明灯光及控制等部分组成。 全部信号的切换及分配均在控制室进行。 二、会议室功能定位及相关配置 1、功能设计 约 120人报告厅设计为会议、小型表演的综合场所。主要用来召开中小型会议,如新闻发布会,产品展示会,报告会,签字仪式,职工培训等。 在功能设计上,要求考虑其多功能性及先进性,应具体表现在以下几个方面: 先进的展示功能 能有效表现与展示各个领域的最新内容。这就需要使用当今最先进的多媒体表现形式:文字、语言、图片、连续影像、电脑文档等。

完善的会议功能 满足各种级别的会议、学术论坛、报告会等各种形式的会议活动。满足新闻发布会、庆功会、签字仪式等公共活动。 强大的培训功能 技术培训、教学、产品介绍;小型年会、月会、局里的例会。 一般性演出功能 能进行一般非专业性的文艺晚会形式的文艺演出,举行各种晚宴、酒会及舞会等。 3、主要配置 会议发言部分(选配 设置手拉手会议发言系统设备,设置台面移动式固定安装设备,支持电子投票表决以及与摄像机配合实现 摄像语音跟踪联动等会议功能。。 现场扩声、还原部分 选用高性能的扩声音响设备,设计为即能满足会议的要求,又能满足小型表演的需要。 高质量大屏幕显示部分 选用高亮度、高清晰的投影设备,丰富会议内容,提高会议档次。选择电动投影幕设备。。 便捷、时尚的集控部分

视频会议流程及简介汇总

视频会议整体操作流程: 在讲解演示的过程中,要考虑到用户的切实需求,同时说明我公司所具备的能力以及我技术人员所拥有的技术水平。 视频会议系统概述 视频会议系统(Videoconferencing System )是一种以视频为主的交互式多媒体通信,它利用现有的图像编码技术,计算机通信技术以及微电子技术,进行本地区或远程地区之间的点对点或多点之间的双向视频,双工音频,以及数据等交互式信息实时通信。视频会议的目的是把相隔多个地点的会议室电视设备连接在一起,使各方与会人员有如身临现场一起开会,进行面对面对话的感觉, 因

此广泛地应用于各类行政会议,远程培训、科技会议、远程教学以及商务谈判等场合中。视频会议系统具有真实、高效、实时的特点,是一种简便而有效的用于管理、指挥以及协同决策的技术手段,在国内各行各业尤其是政府各部门已开始广泛采用,并已发挥出巨大的效益。 视频会议的应用 1).政府级会议 2).商务谈判 3).紧急救援 4).作战指挥 5).银行系统 6).远程教育 7).远程医疗 1.系统介绍 多点控制单元MCU 多点控制单元MCU(Multipoint Control Unit),是多点会议电视的汇接中心,多点会议电视通过MCU来实现音频和视频的混合与切换以及会议共享数据的交换,BYQ-BORYARD MCU-8000系列为标准1U机架式产品,可以方便的放置于网络设备室。 嵌入式会议室终端

系统参数 完全符合TCP/IP技术标准 同时支持8-100路终端接入 同时可进行8个独立会议 网络参数 内置10M/1000M自适应网络接口 低带宽用户支持,每用户带宽上载500K下载1M,可达25F/S 支持DHCP 功能 支持会议控制 支持会议密码保护 支持单画面、多画面模式切换,根据语音能量有选择的进行混音 主席控制和轮巡二种会议切换模式 会议邀请,支持终端会议邀请

会议系统操作说明

. 一、操作说明 1.1、音响系统 1.1.1音响设备开、关机顺序 打开设备,打开电源时序器;关闭系统,关闭电源时序器。 1.1.2功能操作 1、会议时 1.打开设备,把功放旋钮旋到最大; 2、把调音台的输出推子(L、R)推到0DB; 3、根据使用的话筒,把对应的调音台输入通道打开(如有需按下“ON”键)如果使用会议话筒需要把幻想电源开关“POWER+48V”打开。 4、把这路通道推子推到需要的声音响度,但是不能超过0DB,一般在-5DB ——0DB之间,请把这个推子旁边的编组开关打开; 2、播放音乐 1.打开设备,把功放旋钮旋到最大; 2、把调音台的输出推子(L、R)推到0DB; 3、如果播放DVD,把DVD片子放进去,按下播放键,把对应的调音台输入 通道打开(按下“ON”键) 4、把这路通道推子推到需要的声音响度,但是不能超过0DB,一般在-5DB ——0DB之间,请把这个推子旁边的编组开关打开; 3、录音 1.打开设备; 2、把调音台的输出AUX2(在调音台的右边)旋到0DB; 3、把需要录音的话筒通道对应的AUX2旋到-5DB——0DB之间,这样就把这路话筒进入录制了。 4、远程视频会议

1.打开设备,把功放旋钮旋到最大; 2、把调音台的输出AUX1(在调音台的右边)旋到0DB; 3、把远程视频会议这路通道推子推到需要的声音响度,但是不能超过0DB, 一般在-5DB——0DB之间,请把这个推子旁边的编组开关打开; 4、把需要送给远方的话筒通道对应的AUX1旋到-5DB——0DB之间,这样就把这路话筒进入远程视频终端了。 5、注意:不能把远程视频这路的AUX1旋钮打开。 1.2、大屏显示系统 1、打开大屏设备电源; 2、通过无线触摸屏的把大屏打开; 3、通过无线触摸屏选择大屏需要的模式; 4、通过无线触摸屏选择大屏需要的信号输入; 5、注意:如果大屏模式不能调用,请动一下大屏控制电脑的鼠标就可以了; 1.3、矩阵切换系统 1、通过无线触摸屏选择信号的输入输出; 2、如果要把视频信号切换到桌面液晶显示器和控制室的六台监视器,首先通过无线触摸屏的AV矩阵界面把需要显示的视频信号切换到倍线器,再到VGA 矩阵界面把选择的倍线器信号切换到监视器和桌面液晶显示器上即可; 1.4、数字会议和摄像跟踪系统 1.4.1数字会议系统 按下电源开关后,HCS-4100MA/05 会议系统主机上电自动初始化,然后进 入 LCD 初始界面,这包括“菜单”、“开机数量”和“模式”,如下左图所示。此时,按“”键可改变开机数量,按“EXIT”可切换模式。 按“菜单”下的 MENU 键进入菜单设置界面,这包括“网络设置”、“同传设置”、“系统状态”、“测试”、“其它设置”、“关于”六个菜单项,如下

多功能会议室会议系统操作流程指引

会议系统操作指南 本系统由显示系统、扩音系统、中央控制系统构成。规范的操作是系统得以正常运行前提保障,为保证会议的顺利进行因此建议操作员在会议开始前一个小时提前对设备进行开启检查和试运行。 一、设备供电开启 (1)打开设备间配电箱电源让墙面插座供上电,把机柜主电源接入墙面插座接口。 (2)依次打开机柜【总电源】时序器和【中控系统电源】时序器,让机柜上所有设备供上电(开机顺序为从前级逐个开到后级)。二.中控、视频系统 (1)待所有设备供上电后,打开中控触摸屏,连接中控系统WIFI,进入〖中央控制系统〗操作界面。 (2)在主菜单里根据需要选择所要控制的设备进入子菜单界面即可控制(如要控制投影、点击〖投影系统〗后进入控制界面里可以看到〖电源开〗与〖电源关〗,先选择〖电源开〗让投影供电,投影通电后机身蓝色电源指示灯会亮起,然后点击〖开机〗让投影开机启动,待投影机启动后根据会场输入信号选择信号切换如〖HDMI〗,投影即可切换到HDMI输入接口显示。注:电视机控制和投影控制方式相同) (3)HDMI矩阵:点击中控触摸屏进入〖HDMI矩阵〗菜单然后根

据现场使用情况先选择输入再选择输出即可(如把主席台HDMI输入1切换到投影机。先点(输入信号选择)里的〖1〗然后再点(输出信号选择)里的〖5〗即可。投状态。)HDMI影机输入要在.注:HDMI矩阵输入1,2是主席台地插盒接口,3为视频会议摄像机,4,5,6,7为备用。输出1,2,3,4为电视机,5为投影机,6为视频会议移动电视,7 ,8为备用接口) (4)VGA矩阵:点击中控触摸屏进入〖VGA矩阵〗菜单然后根据现场使用情况先选择输入再选择输出即可(如把VGA输入1切换到投影机。先点(输入信号选择)里的〖1〗然后再点(输出信号选择)里的〖5〗即可。投影机输入要在VGA状态。) 注:VGA矩阵输入1,2是主席台地插盒接口,3为视频会议摄像机,4,5,6,7为备用。输出1,2,3,4为电视机,5为投影机,6为视频会议移动电视,7 ,8为备用接口) (5)投影幕布升降要使用中控来完成升降和停止。在〖投影系统〗界面里进行操作。 三.扩音系统 1)使用调音台之前先把调音台的所有推子拉至到底。((2)会议话筒的使用:根据现场实际使用情况将调音台上【会议话筒】通道的推子往上推到相应位置(建议推到10),把【总音量】通道推子推到0即可。会议麦克风按下开关才能被激活,激活时麦头光环呈红色。主席单元具有最高权限,不受其他麦克风控制,且可以控制其他麦克风。按一下主席单元左边的按键,可以把代表单元全部关闭。

会议系统操作使用说明

简介 本简介用于指导用户(根据会议使用要求及与会人数要求)选择恰当的会议室。 一、大会议室 为多功能大型会议厅,可安排400人左右的会议活动或小规模的演出活动。 主要设备及功能特点:大屏幕背投视频播放、数字话筒、会议摄录像监控及储存、中控操作、14路调音台扩声及演出时使用的话筒:模拟话筒、无线话筒、领夹式无线话筒)二、第一会议室(圆桌会议室) 为多功能中型视频会议室,可安排70人左右的会议活动。 主要设备及功能特点:大屏幕正投视频播放、液晶显示器升降、投影机升降、摄像机升降、数字话筒扩声、会议摄像(其中1只为全场机动不固定摄像)监控及刻录、中控操作。 三、第二会议室(课桌会议室) 为中型视频会议室,可安排50至90人左右的会议活动。(视频会议以该会议室为主)主要设备及功能特点:投影幕视频播放、投影机升降、模拟话筒、会议摄像监控及刻录、中控操作。 四、中式、欧式小会议室(第四、第五会议室) 2间均为小型会议室,可安排7人左右的小组会议活动。 主要功能:投影、扩声。 五、局党委会议室 为中小型数字会议室,可安排20人左右的会议活动,主要供局党委小组会议使用。 主要设备及功能特点:大屏幕正投视频播放、投影机升降、数字话筒扩声。

第一章圆桌会议室 1.1会议主要设备介绍: 1. 主功放功放俗称“扩音机”他的作用就是把来自音源或前级放大器的弱信号放大,推动音箱放声。一套良好的音响系统功放的作用功不可没。功放是音响系统中最基本的设备,它的任务是把来自信号源(专业音响系统中则是来自调音台)的微弱电信号进行放大以驱动扬声器发出声音。功率放大器简称功放,可以说是各类音响器材中最大的一个家族了,其作用主要是将音源器材输入的较微弱信号进行放大后,产生足够大的电流去推动扬声器进行声音的重放。由于考虑功率、阻抗、失真、动态以及不同的使用范围和控制调节功能,不同的功放在内部的信号处理、线路设计和生产工艺上也各不 相同 2. 媒体矩阵是美国PEAVEY百威公司经历了九年才开发出来的一种专业控制设备,它由硬件和软件两部分组。成硬件使用的是美国著名专业半导体制造厂Motorola公司生产的56002 DSP芯片;软件是建立在Microsoft Windows界面下的百威专用控制软件包,然后通过电脑将这两部分组合在一起,组成一台智能化专用控制中心,担负调整、控制、设计,组合或运行及参量比较任务。该设备的数据设备库中存有各种不同种类的自动调音台、信号路由器、自动反馈抑制器、自动语音播放器、逻辑门、信号显示器、数字式可调整参数均衡器和图示均衡器、2分频至多分频的分频器、延时器、激励

相关主题