元器件交易网https://www.sodocs.net/doc/417079609.html,
TOSHIBA
TLG1005, TLGD1005, TLPG1005,
TLOE1005, TLYE1005, TLS1005, TLRA1005
TLG1005, TLGD1005, TLPG1005,
TLOE1005, TLYE1005, TLS1005, TLRA1005
Maximum Ratings (T a = 25 ° C)
Electro-Optical Characteristics (T a = 25 ° C)
Product Name Forward Current (DC) I F
(mA)
Reverse Voltage V g (V)Power Dissipation P D
(mW)
Operating Temperature T opr ( ° C )
Storage Temperature T stg
( ° C )
TLPG100525465.0TLG100525462.5TLGD100525462.5 ? 25 ~ 80
? 30 ~ 85
TL YE100525462.5TLOE100525460.0TLS100525465.0TLRA1005
25
4
60.0
Product Name
Emission Spectrum
Luminous Intensity
Forward Voltage
Reverse Current λ P ? λ I V V F I g Typ.
Typ.I F Min.Typ.I F Typ.Max.I F Max.V g TLPG10055552020 4.761220 2.05 2.62054TLG1005567252015.34520 2.05 2.52054TLGD1005570252027.27520 2.1 2.52054TL YE100559013208530020 2.1 2.520504TLOE1005612152015340020 2.0 2.420504TLS100563540208.52520 2.05 2.620504TLRA1005
660
25
20153
450
20 1.85
2.4
20504UNIT
nm
mA
mcd
mA
V
mA
μ A
V
元器件交易网https://www.sodocs.net/doc/417079609.html,
TLG1005, TLGD1005, TLPG1005, TLOE1005, TLYE1005, TLS1005, TLRA1005
TLG1005, TLGD1005, TLPG1005,
TLOE1005, TLYE1005, TLS1005, TLRA1005
TLG1005, TLGD1005, TLPG1005, TLOE1005, TLYE1005, TLS1005, TLRA1005
TLG1005, TLGD1005, TLPG1005,
TLOE1005, TLYE1005, TLS1005, TLRA1005
TLG1005, TLGD1005, TLPG1005, TLOE1005, TLYE1005, TLS1005, TLRA1005
TLG1005, TLGD1005, TLPG1005,
TLOE1005, TLYE1005, TLS1005, TLRA1005
TLG1005, TLGD1005, TLPG1005, TLOE1005, TLYE1005, TLS1005, TLRA1005
TLG1005, TLGD1005, TLPG1005,
TLOE1005, TLYE1005, TLS1005, TLRA1005
Taping Speci?cations:
Packaging
LEDs are packed in an aluminum envelope with silicate to avoid the moisture absorption. After opening the package, storing at following condition is recommended since air extension at soldering according to the moisture absorption in?uences opti-cal characteristics:
-Temperature 5 ~ 30 ° C -Humidity 60% RH (MAX.)
Please execute baking if it has been 6 months under packed or 1 week under opened. Recommended baking condition: 60 °
C, over 12 hours.
元器件交易网https://www.sodocs.net/doc/417079609.html,
TLG1005, TLGD1005, TLPG1005,
TLOE1005, TLYE1005, TLS1005, TLRA1005
Soldering 1.Re?ow soldering:
* It is recommended to use a re?ow furnace of the upper and lower heater type.
* The temperature pro?le as shown in Fig. 1 is recommended for soldering LEDs by the re?ow furnace.
2.
Post solder cleaning:
When cleaning after soldering is needed, the following condition must be adhered to.– Cleaning solvents: AK225 or Alcohol
– Temperature: 50 ° C (122 ° F) MAX. for 30 seconds, or 30 ° C (86 ° F) MAX. for 3 minutes MAX.– Ultrasonic: 300W MAX.
Precaution for Mounting
1.No force to plastic part of LED when LED is under high temperature.
2.No friction using a hard thing to avoid injuring plastic part of LED.
3.
No contact between LED and the other parts, when installing an assembled board into the set.
元器件交易网https://www.sodocs.net/doc/417079609.html,