模具零件名称中英文对照一览表
模具零件名称中英文对照一览表
零件名称ENGLISH NAME 零件名称ENGLISH NAME 上固定板TOP CLAMPING PLATE 母模仁CAVITY
母模板CAVITY PLATE 公模仁CORE
公模板CORE PLATE 母模入子CAVITY INSERT
模脚SUPPRORT BLOCK 母模心子CAVITY INSERT PIN
上顶出板EJECTOR RET PLATE 母模替换入子CAVITY CHANGEABLE INSERT 下顶出板EJECTOR PLATE 公模入子CORE INSERT
下固定板BOTTOM CLAMPING PLATE 公模心子CORE INSERT PIN
隔热板THERMAL INSULATING PLATE 公模替换入子CORE CHANGEABLE INSERT 脱料板RUNNER STRIPPER PLATE 滑块入子SLIDE INSERT
母模垫板CAVITY SUPPORT PLATE 滑块心子SLIDE INSERT PIN
公模垫板CORE SUPPORT PLATE 斜销入子ANLGE LIFTER INSERT 脱料板STRIPPER PLATE 斜销心子ANLGE LIFTER PIN
流道板RUNNER PLATE 流道开关RUNNER SHUT OFF
定位环LOCATING RING T 形块T GIB
注口衬套SPRUE BUSHNG U 形块U GIB
导柱LEADER PIN 拉料销SPRUE PULLER PIN
导套LEADER BUSHING 定位销DOWEL PIN
顶板导柱GUIDE PIN 顶针EJECTOR PIN
顶板导套GUIGE BUSHING 扁销RECTANGLE EJECTOR PIN 大拉杆LARGE PULLER PIN 套筒EJECTOR SLEEVE
小拉杆SMALL PULLER PIN 顶出块EJECTOR BLOCK
支撑柱SUPPORT PILLAR 斜销ANGLE LIFTER
定位块INTERLOCKS 斜销座ANGLE LIFTER BASE
定位柱LOCATION PILLAR 引导块GUIDE BLOCK
开闭器(塑料型) FRICTIONAL PULLER 急回推杆LEVER
弹簧SPRING 冷却棒THERMAL PIN
运输板PL LOCK O 形环O RING
零件名称ENGLISH NAME
滑块SLIDE 隔水板STRAIGHT BUFFLE
滑块座SLIDE BASE 水管接头JIFFY TYTE PLUG
滑轨SLIDE RAIL 油封OIL SEAL
后跟块HELL BLOCK 内六角螺钉SOCKET HEAD CAP SCREW
耐磨板WEAR BLOCK 等高螺钉SOCKET HEAD STRIPPER BLOT
压板RAIL 吊模螺丝EYE BLOT
限位块STOP BLOCK 吊环SAFETY HOIST RINGS
定位夹SLIDE RETAINER 弹簧垫圈SPRING WASHER
定位珠SLIDE RETAINER 加长型水管接头EXTENSION JIFFY TYTE PLUG
急回机构POSITIVE EARLY EJECTOR RETURN
急回推杆LEVER
固定块MOUNT AND COVER PLATE 弹簧片ARM
中文名称
英文名称
中文名称
英文名称
MOLD BASE
内六角螺丝
LOCATING RING
EJECTOR
SPRUE BUSH
SPRING
HOT RUNNER
无头螺丝
SET SCREW CAVITY
平头螺丝
定位拨珠
BALL CATCH
前模镶件
CAVITY INSERT EJECTOR SLEEVE 后模镶件
CORE INSERT BLADE EJECTOR
行位(滑块)
有托顶针SHOULDER EJECTOR WEDGE
SPRUE PULLER ANGLE PIN
WEAR BLOCK
PO LOCK JIGGLE
导柱辅助器TAPERD SET EJECTOR BLOCK 散打螺丝STRIPPER BOLT STOP BLOCK
等高螺丝(拉杆) AS SCREW EJECTION PLATE HYDRAULIC LEADER BLOCK 日期指示器DATE INDICATE WEDGE BLOCK
环保标记章SUPPORT PILLAR AIR JET
RM MARKER
LOCATING PIN
GUIDED EJECTION
支撑杆(撑头)
HYDRAULIC MOTOR
塑胶模具常用零件中英文对照表BRONZE
SEAL RING
SPIRAL TUBE
STOP PIN
螺旋水套
开关装置
SWITCH
STAGE EJECTOR
COPPER
SPACE BLOCK
WATER PIPE
液压马达
INSERT PIN
模具方面的中英文对照
模具方面的中英文对照【二】 2007-05-09 22:35 塑料成型模具的主要设计要素 脱模距 stripper distance 脱模斜度 draft 投影面积 projected area 最大开距 maximum daylight; open daylight 闭合高度 mould-shut height 抽芯距 core-pulling distance 抽芯力 core-pulling force 脱模力 ejector force 开模力 mould opening force 模内压力 internal mould pressure; cavity pressure 成型压力 moulding pressure 背压环 back-up ring 1 bar = 14.5psi 高压接头 bite type fitting 液压马达 hydraulic motor 冷却水流量计 waterflow regulator 打磨器材 abrasive material 打磨砂轮 grinding wheels 切割砂轮 cutting wheels 码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具 piping tools 高压力软管 high pressure hose 风管,水软管 air .water hose 高压油表 pressure gauge 压力油喉 hydraulic hoses 光塑检测 photoelastic testing 吹塑模 plastic blow mould 注塑模 plastic injection mould 冲扎复合模 blank & form compound die 精密冲模 precision blanking die 熔料流动率 MFR=melt flow rate 熔料流动指数 MET=melt flow index 推板导柱 guide pin for ejector plater 座板 clamping plate 垫块 space block(plate) 推板 ejector block(plate) afdek plate 档尘板 guide stripe 行位后板 cavity sub-insert 前模镶件 core sub-insert 后模镶件 sprue puller insert 扣针镶件
常用模具零件中英文对照表
常用模具零件中英文对照表 2005-12-19 14:51:17中国注塑网 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin
模具DFM常用中英文对照
DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小，导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位，强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角，填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚，会有缩水，建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上，请确认是否接受？ Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角，以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， stick
模具中英文对照表
landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具
模具常用术语中英文对照表
"R，L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
模具方面的中英文对照
查看文章模具方面的中英文对照【二】2007-05-09 22:35 塑料成型模具的主要设计要素脱模距stripper distance 脱模斜度draft 投影面积projected area 最大开距maximum daylight;open daylight 闭合高度mould-shut height 抽芯距core-pulling distance 抽芯力core-pulling force 脱模力ejector force 开模力mould opening force 模内压力internal mould pressure;cavity pressure 成型压力moulding pressure 背压环back-up ring 1 bar = 14.5psi 高压接头bite type fitting 液压马达hydraulic motor 冷却水流量计waterflow regulator 打磨器材abrasive material 打磨砂轮grinding wheels 切割砂轮cutting wheels 码模夹（注塑机使用） mould clamps; lifting clamps 小五金工具piping tools 高压力软管high pressure hose 风管,水软管air .water hose 高压油表pressure gauge 压力油喉hydraulic hoses 光塑检测photoelastic testing 吹塑模plastic blow mould 注塑模plastic injection mould 冲扎复合模blank & form compound die 精密冲模precision blanking die 熔料流动率MFR=melt flow rate 熔料流动指数MET=melt flow index 推板导柱guide pin for ejector plater 座板clamping plate 垫块space block(plate) 推板ejector block(plate) afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件 stage ejector 顶棍
模具中英文对照
中英名詞對照 一.劃 一般商業用模座：Commercial die set 二.劃 V字形靠柵：V-gaging 三.劃 1.工作單：Operation sheet 2.三角形沖片：Triangular blank 3.小沖床沖模：Sub-press die 4.工作流程單：Route sheet 5.下驅動沖床：Underdrive press 6.三角形打料板：Knockout plate spider 7.工具校驗部門：Tool inspection depart 四.劃 1.分圓：Detail drawing 2.止動銷：Dutchman 3.雙行排列：Layout double-raw 4.分裝模體：Split die block 5.方頭駐螺：Square-head set screw 6.中心莰入件：Center insert 7.水硬工具鋼：Water hardening tool Steel 1.尺寸與注記：Dimensions and notes 2.六方埋頭螺絲：Socket cap screw 3.孔徑尺寸注記：Dimension of hole 4.手動定位裝置：Finger stop 5.雙排沖切設計（排列）：Double-raw layout 五道次沖切排列：Rive-station layout 五.劃 1.切圓：Cutting ring 2.切邊：Trimming 3.打料桿：Knockout rod 4.避位：Stiffening 5.半銅模座：Semi-steel die set 6.另件布置：Part layout 7.引伸沖模：Dies drawing 8.皮料加工：Finish of sheet 9.打料柱塞：Knockout plunger 10.打料裝置：Knockouts 11.可卸道筒：Demountable guide bushing 1.切斷沖模：Gutoff die 2.切邊裕度：Allowance or trimming 3.切邊沖模：Trimming die 4.平頭埋頭螺：Flat head screw socket 1.四道柱沖床：Four-post press 2.四道柱模座（沖模模座）：Four-post die sct 1.引伸零件展開：Development of drawn parts 1.半陰式定位銷：Semi-blind dowel 2.平行四邊形沖片：Parallelogram shaped blank 六.劃 1.沖扁（沖鍛）：Stamping 2.沖頭把：Punch shank 3.先道桿：Pilot 4.沖片毛邊：Burrside of blank 5.沖片加工：Blanking 6.沖片沖頭：Blanking 7.沖切長口：Slitting 8.沖孔沖床：Punch press 9.沖孔沖頭：Piercing punch 10.沖孔沖模：Die piercing 11.沖片沖模：Blanking die 12.沖片設計（安排）：Blank layout 13.沖片面積：Area of blank 14.沖床附件：Press accessories 15.沖床動力：Power for press 16.沖床構造：Press construction 17.自動沖床：Automated press 18.先道桿簧：Spring pilot 19.曲軸總成：Crankshaft assembly 20.沖模套筒：Die bushing 21.沖模間隙：Die Clearance 22.沖模截塊：Die section 23.沖模模座：Die set 24.沖彎公式：Bend formula
模具--中英文对照
dowel pin 定位梢 draft 拔模锥度 draw bead 张力调整杆 drive bearing 传动轴承 ejection pad 顶出衬垫 ejector 脱模器 ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢 ejector plate 顶出板 ejector rod 顶出杆 ejector sleeve 顶出衬套 ejector valve 顶出阀 eye bolt 环首螺栓 filling core 椿入蕊 film gate 薄膜形浇口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销 flash gate 毛边形浇口 flask 上箱 floating punch 浮动冲头 gate 浇口 gate land 浇口面 gib 凹形拉紧楔 goose neck 鹅颈管
guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶头冲孔 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头 insert 嵌件 insert pin 嵌件梢 king pin 转向梢 king pin bush 主梢 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner
模具DFM常用中英文对照
DFM常用中英文对照 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印，但 在浇口附近可以避免。 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。 4.Venting insert here has flash 排气镶件处有飞边 5.Venting gap between inserts is too big 镶件处的排气槽过大 6.Stress mark on the cosmetic surface 产品外表面上有压痕 7.Uneven thickness 不平均的产品壁厚 8.Unreasonable product structure 不合理的产品结构 9.Injection speed is high 注塑压力过高 10.There is black spot on the cosmetic surface 产品外表面上有黑色点 11.There is flash on the product 产品有飞边 12.there is sink mark on the cosmetic surface 产品外表面上有缩痕 13.Gate size is not reasonably 浇口尺寸不合理 14.There is argent spot 这里有亮点（银色斑点） 15.The plastic of first shot didn't meet high temperature. 塑料的第一胶不会有很高的温度。 16.Make sure the core float plate was closed before lifter completely return to correct position 确认 lifter完全回位时core侧浮动板已经复位 17.Make sure the ejector system is smooth 确认顶针系统移动平稳 18.Add early return structure to protect lifter return to correct position 增加先复位机构保护lifter回到正确 位置。 19.Propose to add draft on slider side wall and draw polish. 建议增加 slider的角度和抛光角度。 20.It is too thin and very difficult to inject fully, and weakness wall will have risk of the part function 该 处壁厚过薄而造成很难去填充完整，薄壁将会有产品功能上的风险。 21.These are will have sink marks due to uneven thickness, propose to reduce plastic. 壁厚不均匀容易产生缩印， 建议在该处减胶。 22.These are will have sink marks due to ribs opposite. 正面的筋位易导致背面产生缩印。 23.Please confirm the 3D part thickness whether has including painting thickness or not? 请确认产品的设计是否
五金模具常用专业术语中英文对照表[1]
五金模具常用专业术语中英文对照表 上模座upper die set成型公form punch 脱料板stripper 垫板subplate/backup plate 下模座die plate滑块CAM slider 垫脚parallel 误检misfeeder 托板mounting plate顶料销kick off 初始管位first start pin带肩螺丝shoulder screw 两用销lifter pin氮气汽缸gas spring 弹簧护套spring cage 拔牙螺丝jack screw 侧冲组件cam section 导正装置guide equipment 漏废料孔slug hole刀口trim line 加强装置enhance equipment 入子insert 护套bushing 整形公restrike forming punch 止挡板stop plate 挂台head 扣位pocket of head 导柱guide post 导套guide bushing 油嘴oil nipple 接刀口mismatch/cookie bites 限位块stop block 挡块stopper 浮块lifter 压块keeper 靠块heel 对正块alignment block 简易模prototype tooling 检具gage/checking fixture 料带图strip layout 闭合高度shut hight 俯视图top view 料带strip 公差tolerance 正视图front view 走位travel 避位/空pocket 退磁demagnetization 间隙clearance 真空热外理vacuum heat treatment 镗孔mill hole 表面外理surface coasting 镀钛TD coasting 沉头counter sink 精锣finish mill 线割wire cutting 穿丝孔first wire hole 斜度taper 镭射laser-cut 上夹板/固定座holder/retainer 下模座lower die set 成刑母公forming die 电火花EDM 码模槽mounting slot 球锁紧固定座ball-lock 导尺rail 球锁紧凸模BALL--LOCK 送料板rail plate 外购out sourcing 倒角chamfer 清角SCRAP CHOPPER 销钉dowel 尖角sharp --angle 普通弹簧coil spring 展开图EXPENSINg DWG 三打螺丝spool 镶件insert 毛刺burr 键销key 插针pilot pin
模具常用中英文对照
模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level
材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner V ents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带 Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug
模具用语中英文对照
模具用语中英文对照 198各式模具分类用语中英文对照 landed plunger mold 有肩柱塞式模具 burnishing die 挤光模Www_17He_com landed positive mold 有肩全压式模具 button die 镶入式圆形凹模一起呵_英语站loading shoe mold 料套式模具center-gated mold 中心浇口式模具一起呵@英语站loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模一起呵@英语站louvering die 百叶窗冲切模 composite dies 复合模具英.语.站 manifold die 分歧管模具一起呵_英语站counter punch 反凸模英语.站 modular mold 组合式模具 double stack mold 双层模具17He~Com multi-cavity mold 多模穴模具 electroformed mold 电铸成形模 multi-gate mold 复式浇口模具 expander die 扩径模一起呵.英语.站offswt bending die 双折冷弯模具
extrusion die 挤出模英语.站 palletizing die 叠层模一起呵@英语@站family mold 反套制品模具一.起.呵.英语站plaster mold 石膏模 17he_com blank through dies 漏件式落料模一porous mold 通气性模具duplicated cavity plate 复板模一起呵@英语站positive mold 全压式模具 fantail die 扇尾形模具 17he_com pressure die 压ingot mold 钢锭模 punching die 落料模 lancing die 切口模英语.站 raising(embossing) 压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 无流道冷料模具一起呵_英语站 sectional die 对合模具 英.语.站 segment mold 组合模一起_呵_英语站 semi-positive mold 半全压式模具一起_呵_英语站 shaper 定型模套 single cavity mold 单腔模具
模具常用术语中英文对照
模具常用术语中英文对照 模具常用术语中英文对照 中文英文 模芯Parting Core 局部视图Partial View 冷料# ColdSllig 线切割Wire E.D.M 轮廊Contour 螺纹孔Tapping Hole 连接件Fittings 斜针AnglePin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机SpecificPress 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-LeaderdPin 镶件Mold Insert 加硬Hapden 唧嘴Sprue 设计筒图DesignPreliminary 名称块表 Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试LeakTest 流道排气Runner Vents 抛光Draw Polish 侧抽芯SideAction 中文英文加强筋Reinforcing 三角撑Gusset 柱子Bosse 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔Handl Ing Hole 运输安全带Moldstrap 码
模槽ClampSlot
撑头Support Pillar 螺牙1/2-13 EyeBolt 1/2-13Tap 导柱位LeaderPin Location 耐落胶Teflon Paste 偏移量Offset 水塞 Water Line Plig 撬模脚PpySlot 重新加工Reworked 配件Components 补偿 Compensation 平面度 Parallel 倒角 Chamfer 模胚 Mold Base 热嘴 Hotnozzle 火花机 Edm 熔接线 Weildline 压机 Press 晒纹 Texturing 梯形Trapezoio 凸缘、法兰Flange 模具常用术语中英文对照 中文英文 方铁 SpacerBlock 顶针板 Ejector Plate
模具零件名称中英文对照一览表
模具零件名称中英文对照一览表 零件名称ENGLISH NAME 零件名称ENGLISH NAME 上固定板TOP CLAMPING PLATE 母模仁CAVITY 母模板CAVITY PLATE 公模仁CORE 公模板CORE PLATE 母模入子CAVITY INSERT 模脚SUPPRORT BLOCK 母模心子CAVITY INSERT PIN 上顶出板EJECTOR RET PLATE 母模替换入子CAVITY CHANGEABLE INSERT 下顶出板EJECTOR PLATE 公模入子CORE INSERT 下固定板BOTTOM CLAMPING PLATE 公模心子CORE INSERT PIN 隔热板THERMAL INSULATING PLATE 公模替换入子CORE CHANGEABLE INSERT 脱料板RUNNER STRIPPER PLATE 滑块入子SLIDE INSERT 母模垫板CAVITY SUPPORT PLATE 滑块心子SLIDE INSERT PIN 公模垫板CORE SUPPORT PLATE 斜销入子ANLGE LIFTER INSERT 脱料板STRIPPER PLATE 斜销心子ANLGE LIFTER PIN 流道板RUNNER PLATE 流道开关RUNNER SHUT OFF 定位环LOCATING RING T 形块T GIB 注口衬套SPRUE BUSHNG U 形块U GIB 导柱LEADER PIN 拉料销SPRUE PULLER PIN 导套LEADER BUSHING 定位销DOWEL PIN 顶板导柱GUIDE PIN 顶针EJECTOR PIN 顶板导套GUIGE BUSHING 扁销RECTANGLE EJECTOR PIN 大拉杆LARGE PULLER PIN 套筒EJECTOR SLEEVE 小拉杆SMALL PULLER PIN 顶出块EJECTOR BLOCK 支撑柱SUPPORT PILLAR 斜销ANGLE LIFTER 定位块INTERLOCKS 斜销座ANGLE LIFTER BASE 定位柱LOCATION PILLAR 引导块GUIDE BLOCK 开闭器(塑料型) FRICTIONAL PULLER 急回推杆LEVER 弹簧SPRING 冷却棒THERMAL PIN 运输板PL LOCK O 形环O RING
模具专业英文术语大全
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内模：core insert 行位（滑块）：slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin
模具英文缩写对照
模芯 Parting Core 局部视图 Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊 Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针 Angle Pin 接合 Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press 水嘴接头 Water Fittings 螺纹 Eyebolt Thread 回针 Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件 Mold Insert 加硬 Harden 唧嘴 Sprue 设计筒图 Design Preliminary 名称块表 Title Block 版本标识 Revision Level 材料清单 Stock List 制模 Build Mold 手动滑块 Hand Slide 漏水测试 Leak Test 流道排气 Runner Vents 抛光 Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑 Gusset 柱子 Bossed 出模斜度 Draft 外廊 Contour 落单会议 Kick-Off Meeting 装卸孔 Handling Hole 运输安全带 Moldstrap 码模槽 Clamp Slot 撑头 Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞 Water Line Plug 撬模脚 Ppy Slot