搜档网
当前位置:搜档网 › 米沃奇m18冲击钻起子机2453-20爆炸图,分解图b

米沃奇m18冲击钻起子机2453-20爆炸图,分解图b

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 W. Lisbon Road, Brook ? eld, WI 53005

Drwg. 2

FIG. PART NO. DESCRIPTION OF PART NO. REQ. 1 31-12-0575 Rubber Cap (1) 2 45-22-2653 Sleeve (1) 3 34-60-0725 Retaining Ring (1) 4 45-88-1880 Washer (1) 5 40-50-1470 Spring (1) 6 --------------- Anvil Bushing (Not Shown) (1) 9 45-88-2135 Plastic Washer (1) 10 02-02-0170 3.5mm Steel Ball (1) 11a 42-06-0720 1/4" Hex Anvil (1) 12 02-02-1300 5mm Steel Ball (1) 19 02-02-0180 4.7mm Steel Ball (2) 22 --------------- Ball Bearing (1) 23 --------------- Gearcase End Cap (1) 24 --------------- Ring Gear (1) 25 44-66-1065 Gearcase End Cap Assembly (1) 27 --------------- Stator Assembly (1) 28 45-30-0300 Rubber Slug (4) 34 --------------- PCBA (1) 35 --------------- On-Off Switch (1) 36 --------------- Terminal Block Assembly (1) 37 45-24-0810 Fwd/Rev Shuttle (1) 38 40-50-1135 Spring (1) 42 42-70-0055 Housing Connection Clip (1) 43 --------------- Left Handle Halve with Fuel Gauge (1) 44 42-70-0580 Belt Clip (1) 45 --------------- Belt Hook Screw (1) 46 06-82-1090 M3 x 7mm Pan Hd. Plastite Screw (2)

FIG.

PART NO. DESCRIPTION OF PART NO. REQ. 47 --------------- Right Handle Halve (1) 48 12-20-2435 Service Nameplate (Not Shown) (1) 49 42-55-1060 Carrying Case (1) 50 06-82-7236 4-20 x 5/8" Pan Hd. Plastite T-10 Scr (7) 51 40-50-0012 Anvil Spring (1) 56 14-30-1170 Gearcase Assembly (1) 57 28-50-0920 Front Gearcase with Bushing (1) 58 42-70-0490 Belt Clip Assembly (1) 59 16-07-0420 Rotor Assembly (1) 60 31-44-2453 Handle Assembly (1) 61 14-30-1200 Impacting Assembly (1) 62 14-20-1520 Electronics Assembly (1) 63 23-66-2455 POP Switch (1) 64 10-20-2845 Spanish/French Warning Label (1)

FIG. LUBRICATION

(Type 'J' Grease, No. 49-08-4220):10,11a Lightly coat front washer surface of anvil (11a) with grease, place a dab in the ball slot of anvil.

24,61 Lightly coat the I.D. of the ring gear (24) and the center of

the planet gears of impacting assembly with grease. 57 Coat inside of bushing inside front gearcase with grease. 59

Coat pinion of rotor assembly (59) with grease.

Updated M12? Handle Sets utilize Housing Connection Clips No. 42-70-0055 and 42-70-0058. (The 42-70-0058 is a preferred upgrade). Install this clip design by aligning the side rails of the clip with the two slots in the handle set. Gently push into place with the aid of a small flat blade screwdriver or a similar instrument.

Be sure that the clip is properly seated in both slots and that the tab of the clip snaps down in the round dimpled cavity of the handle set. Be sure that the clip is flush to sub-flush to the end of the handle set. To remove the clip, use the same small flat blade screwdriver or a similar instrument and lift up on the clip tab while pushing the clip out of the handle set. Use a needle nose pliers to gently rebend the clip tab if necessary. If the tab on the clip is damaged during this process and is loose or will not stay in place, replace with a new 42-70-0058 clip. Early M12? Handle Sets utilize Housing Connection Clip No. 42-70-0055. Install this clip design by aligning the side rails of the clip with the two slots in the handle set. Gently

push into place with the aid of a small flat

blade screwdriver or a similar instrument. Be sure that the clip is properly seated in both

slots and that the clip is flush to sub-flush to

the end of the handle set. To remove the clip, use the same small flat blade screwdriver or a similar instrument and push the clip out of the handle set. If the clip is loose or will not stay in place, a needle nose pliers can be used to gently bend/pinch the side rails of the clip. If

the clip is damaged do not use, replace with a new 42-70-0055 housing clip.

Newer M12? Handle Sets utilize Housing Connection Clip No. 42-70-0058. Install this clip design by aligning the side rails of the clip with the two slots in the handle set. Gently

push into place with the aid of a small flat blade screwdriver or a similar instrument. Be sure

that the clip is properly seated in both slots and that the tab of the clip snaps down in the rectangular cavity of the handle set. Be sure

that the clip is flush to sub-flush to the end of the handle set. To remove the clip, use the same small flat blade screwdriver or a similar instrument and lift the clip tab out of the cavity while pushing the clip out of the handle set.

Use a needle nose pliers to gently rebend the clip tab if necessary. If the tab on the clip is damaged during this process and is loose or

will not stay in place, replace with a new

42-70-0058 clip.

相关主题